4 修訂歷史記錄

Changes from H Revision (November 2017) to I Revision

• Added figure titles to the Application CurvesGo

Changes from G Revision (October 2016) to H Revision

• Deleted "or unknown" from Auto subsectionGo
• Deleted "and Auto Modes" from TSTART Indicators of Detect and Class Failures subsectionGo
• Changed fault conditions for Auto mode in Detect and Class Failure Indicators tableGo
• Added information to Step 2 in Start/ILIM Event Register subsectionGo

Changes from F Revision (July 2016) to G Revision

• Deleted the MAX value of 150 mA from I_GO- in the Electrical CharacteristicsGo

Changes from E Revision (March 2016) to F Revision

• Legacy Device Detection, Changed the paragraph, "in general,..."Go
• Changed section From: Independent Operation when the Bit is Set To: Independent Operation when the AUTO Bit is SetGo
• I2C Slave Address and AUTO Bit Programming, Added NOTE: "When using I²C scan..."Go
• Start/ILIM Event Register, Changed the third list item From: "Detect fault or classification unknown,.." To: "Overcurrent or class mismatch on second finger in Semi-Auto or Manual Mode." Go
• Timing Configuration Register, Added new NOTE under TLIM[1:0]: " If ILIM and ICUT are set to same value..."Go
• Timing Configuration Register, Added new NOTE under TICUT[1:0]: " If ILIM and ICUT are set to same value..."Go
• Two-Event Classification Register, Changed the second list item to include: "CLEn is set or a" Go
• Replaced Figure 58Go

Changes from D Revision (September 2015) to E Revision

• Added 設置）在特性“半自動模式”中添加了說明Go
• Updated Pin Functions tableGo
• Added new Figure 37Go
• Added new Functional Block DiagramGo
• Changed note in A/D Converter and I2C InterfaceGo
• Changed the Note in I2C Slave Address and AUTO Bit ProgrammingGo
• Added note to I2C Slave Address and AUTO Bit ProgrammingGo
• Changed I²C slave address register note.Go
• Added new Figure 43Go
• Added a note to Manual about type 2 power 2 event classification.Go
• Added content to Semi-AutoGo
• Added "PoEPn" column to Bits DescriptionGo
• Added a note to PoE Plus RegisterGo

Changes from C Revision (June 2015) to D Revision

• Added reference note to Figure 5 and Figure 6Go
• Changed RESET note to add addition reference link. Go
• Added SDAO pin note. Go
• Changed I²C Slave Address and AUTO Bit Programming note. Go
• Added Figure 42, I²C/SMBus Interface Slave Address Programming Protocol. Go
• Added note 3 to Table 10Go
• Changed Connections on Unused Ports section.Go
• Added reference link to the VPWR-RESET Sequencing note.Go

Changes from B Revision (April 2015) to C Revision

• Added Figure 5 and Figure 6Go
• Changed Figure 36, Disconnected AIN pin from GNDGo
• Added SHTDWN note.Go
• Added RESET note. Go
• Added Device Power On Initialization sectionGo
• Added note 2 to Table 10Go
• Added Port n Status Register note.Go
• Added Operating Mode Register Command note. Go
• Added Operating Mode Register Bit Description note. Go
• Added Detect/Class Enable Register Command note. Go
• Added Detect/Class Restart Register Command note.Go
• Added Power Enable Register Command note.Go
• Added Power Enable Register Bit Descriptions note.Go
• Added Reset Register Command note.Go
• Added Reset Register Bit Descriptions note. Go
• Changed Figure 46, Disconnected AIN pin from GNDGo
• Changed Figure 48, Disconnected AIN pin from GNDGo
• Changed Figure 49, Disconnected AIN pin from GNDGo
• Changed Figure 50, Disconnected AIN pin from GNDGo
• Changed Q_Pn description in Per Port ComponentsGo
• Changed maximum VDD supply current from 10 mA to 6 mA in first paragraph and changed wording in second paragraph of VDD.Go
• Added VPWR-RESET SequencingGo

Changes from A Revision (June, 2014) to B Revision

• Changed VDD current consumption from 10 mA (MAX) to 6.0 mA (MAX)Go
• Deleted Processor watchdog trip delay specification.Go
• Added When using the I²C interface note. Go
• Added When using the I²C interface note. Go
• Changed FULL SCALE VALUE from 146.2°C to 150°C (typical).Go
• Changed LSB VALUE from 0.652°C to 7°C.Go
• Added Temperature sensor performance note.Go

Changes from * Revision (March 2014) to A Revision

• Added 完整版 TPS23861 IEEE 802.3at 四端口以太網供電 PSE 控制器數據表。Go