SLUSFH4A March 2025 – July 2025 BQ25858-Q1 , BQ25858B-Q1
PRODUCTION DATA
- 1
- 1 Features
- 2 Applications
- 3 Description
- 4 Device Comparison
- 5 Pin Configuration and Functions
- 6 Specifications
-
7 Detailed Description
- 7.1 Overview
- 7.2 Functional Block Diagram
- 7.3
Feature Description
- 7.3.1 Device Power-On-Reset
- 7.3.2 Device Power-Up From Battery Without Input Source
- 7.3.3 Device Power Up From Input Source
- 7.3.4 Power Management
- 7.3.5 Bidirectional Power Flow and Programmability
- 7.3.6 Switching Frequency Dithering Feature
- 7.3.7 Integrated 16-Bit ADC for Monitoring
- 7.3.8 Status Outputs (PG, STAT and INT)
- 7.3.9
Protections
- 7.3.9.1
Voltage and Current Monitoring
- 7.3.9.1.1 VAC Over-voltage Protection (VAC_OVP)
- 7.3.9.1.2 VAC Under-voltage Protection (VAC_UVP)
- 7.3.9.1.3 Reverse Mode Over-voltage Protection (REV_OVP)
- 7.3.9.1.4 Reverse Mode Under-voltage Protection (REV_UVP)
- 7.3.9.1.5 DRV_SUP Under-voltage and Over-voltage Protection (DRV_OKZ)
- 7.3.9.1.6 REGN Under-voltage Protection (REGN_OKZ)
- 7.3.9.2 Thermal Shutdown (TSHUT)
- 7.3.9.1
Voltage and Current Monitoring
- 7.3.10 Serial Interface
- 7.4 Device Functional Modes
- 7.5 BQ25858-Q1/858B-Q1 Registers
-
8 Application and Implementation
- 8.1 Application Information
- 8.2
Typical Applications
- 8.2.1
Typical Application (Buck-Boost configuration)
- 8.2.1.1 Design Requirements
- 8.2.1.2
Detailed Design Procedure
- 8.2.1.2.1 ACUV / ACOV Input Voltage Operating Window Programming
- 8.2.1.2.2 Switching Frequency Selection
- 8.2.1.2.3 Inductor Selection
- 8.2.1.2.4 Input (VAC) Capacitor
- 8.2.1.2.5 Output (VBAT) Capacitor
- 8.2.1.2.6 Sense Resistor (RAC_SNS and RBAT_SNS) and Current Programming
- 8.2.1.2.7 Converter Fast Transient Response
- 8.2.1.3 Application Curves
- 8.2.2 Typical Application (Buck-only configuration)
- 8.2.1
Typical Application (Buck-Boost configuration)
- 8.3 Power Supply Recommendations
- 8.4 Layout
- 9 Device and Documentation Support
- 10Revision History
- 11Mechanical, Packaging, and Orderable Information
封裝選項
請參考 PDF 數據表獲取器件具體的封裝圖。
機械數據 (封裝 | 引腳)
- RRV|36
散熱焊盤機械數據 (封裝 | 引腳)
- RRV|36
訂購信息
8.2.1.2.1 ACUV / ACOV Input Voltage Operating Window Programming
The input voltage operating window is programmed by an ACUV / ACOV window with a resistor divider from VAC to GND. The top resistor, RAC1 is typically selected as 1,000k? to minimize the input voltage leakage current. Assuming the desired trip-points for under-voltage and over-voltage protection are labeled VVACUVP and VVACOVP, the resistor divider required can be calculated as follows.
Figure 8-2 ACUV and ACOV Resistor DividerEquation 6.
Equation 7.
For the default device operating window of 4.4V to 70V, the ACUV can be pulled up directly to VAC, while the ACOV can be pulled directly to GND.