SLUSFH4A March 2025 – July 2025 BQ25858-Q1 , BQ25858B-Q1
PRODUCTION DATA
- 1
- 1 Features
- 2 Applications
- 3 Description
- 4 Device Comparison
- 5 Pin Configuration and Functions
- 6 Specifications
-
7 Detailed Description
- 7.1 Overview
- 7.2 Functional Block Diagram
- 7.3
Feature Description
- 7.3.1 Device Power-On-Reset
- 7.3.2 Device Power-Up From Battery Without Input Source
- 7.3.3 Device Power Up From Input Source
- 7.3.4 Power Management
- 7.3.5 Bidirectional Power Flow and Programmability
- 7.3.6 Switching Frequency Dithering Feature
- 7.3.7 Integrated 16-Bit ADC for Monitoring
- 7.3.8 Status Outputs (PG, STAT and INT)
- 7.3.9
Protections
- 7.3.9.1
Voltage and Current Monitoring
- 7.3.9.1.1 VAC Over-voltage Protection (VAC_OVP)
- 7.3.9.1.2 VAC Under-voltage Protection (VAC_UVP)
- 7.3.9.1.3 Reverse Mode Over-voltage Protection (REV_OVP)
- 7.3.9.1.4 Reverse Mode Under-voltage Protection (REV_UVP)
- 7.3.9.1.5 DRV_SUP Under-voltage and Over-voltage Protection (DRV_OKZ)
- 7.3.9.1.6 REGN Under-voltage Protection (REGN_OKZ)
- 7.3.9.2 Thermal Shutdown (TSHUT)
- 7.3.9.1
Voltage and Current Monitoring
- 7.3.10 Serial Interface
- 7.4 Device Functional Modes
- 7.5 BQ25858-Q1/858B-Q1 Registers
-
8 Application and Implementation
- 8.1 Application Information
- 8.2
Typical Applications
- 8.2.1
Typical Application (Buck-Boost configuration)
- 8.2.1.1 Design Requirements
- 8.2.1.2
Detailed Design Procedure
- 8.2.1.2.1 ACUV / ACOV Input Voltage Operating Window Programming
- 8.2.1.2.2 Switching Frequency Selection
- 8.2.1.2.3 Inductor Selection
- 8.2.1.2.4 Input (VAC) Capacitor
- 8.2.1.2.5 Output (VBAT) Capacitor
- 8.2.1.2.6 Sense Resistor (RAC_SNS and RBAT_SNS) and Current Programming
- 8.2.1.2.7 Converter Fast Transient Response
- 8.2.1.3 Application Curves
- 8.2.2 Typical Application (Buck-only configuration)
- 8.2.1
Typical Application (Buck-Boost configuration)
- 8.3 Power Supply Recommendations
- 8.4 Layout
- 9 Device and Documentation Support
- 10Revision History
- 11Mechanical, Packaging, and Orderable Information
封裝選項
請參考 PDF 數據表獲取器件具體的封裝圖。
機械數據 (封裝 | 引腳)
- RRV|36
散熱焊盤機械數據 (封裝 | 引腳)
- RRV|36
訂購信息
7.3.3.1 VAC Operating Window Programming (ACUV and ACOV)
The VAC operating window can be programmed via the ACUV and ACOV pins using a three-resistor divider from VAC to PGND as shown in Figure 7-1.
Figure 7-1 ACUV and ACOV ProgrammingWhen VACUV falls and reaches VACUV_DPM, the device enters input voltage regulation, thereby reducing the output current. VACUV continues falling below VREF_ACUV, the device automatically stops the converter and the PG pin pulls high.
When VACOV rises above VREF_ACOV, the device automatically stops the converter and the PG pin pulls high.
The following equations govern the relationship between the resistor divider and the target operating voltage window programmed by ACOV and ACUV pins:
If unused, tie ACUV to VAC and ACOV to PGND in order to apply the internal VAC operating window (VVAC_OP).