ZHCSY78 March 2025 UCC5350L-Q1
PRODUCTION DATA
| 參數 | 測試條件 | 最小值 | 典型值 | 最大值 | 單位 | |
|---|---|---|---|---|---|---|
| 電源電流 | ||||||
| IVCC1 | 輸入電源靜態電流 | 1.67 | 2.4 | mA | ||
| IVCC2 | 輸出電源靜態電流 | 1.1 | 1.8 | mA | ||
| VCC1 電源電壓欠壓閾值 | ||||||
| VVCC1_ON | VCC1 UVLO 上升閾值 | 2.6 | 2.8 | V | ||
| VVCC1_OFF | VCC1 UVLO 下降閾值 | 2.4 | 2.5 | |||
| VVCC1_HYS | VCC1 UVLO 閾值遲滯 | 0.1 | ||||
| VCC2 電源電壓欠壓閾值和延遲 | ||||||
| VVCC2_ON | VCC2 UVLO 上升閾值 | 12 | 13 | V | ||
| VVCC2_OFF | VCC2 UVLO 下降閾值 | 10.3 | 11 | |||
| VVCC2_HYS | VCC2 UVLO 閾值遲滯 | 1 | ||||
| 邏輯 I/O | ||||||
| VIT+(IN) | 輸入高電平閾值電壓 | 0.55*VCC1 | 0.7*VCC1 | V | ||
| VIT-(IN) | 輸入低電平閾值電壓 | 0.3*VCC1 | 0.45*VCC1 | |||
| Vhys(IN) | 輸入閾值遲滯 | 0.1*VCC1 | ||||
| IIH | INx 引腳高電平輸入漏電流 | IN+ = VCC1 | 40 | 240 | μA | |
| IIL | INx 引腳低電平輸入漏電流 | IN- = GND1 | -240 | -40 | μA | |
| IIL | IN 引腳低電平輸入漏電流 | IN- = GND1 - 5V | -310 | -80 | μA | |
| 柵極驅動器級 | ||||||
| IOH | 峰值輸出拉電流 | IN+ = 高電平，IN- = 低電平 | 5 | 10 | A | |
| IOL | 峰值輸出灌電流 | IN+ = 低電平，IN- = 高電平 | 5 | 10 | A | |
| VOH | 高電平輸出電壓 (VCC2 - OUT) | IOUT = -20mA | 100 | 240 | mV | |
| VOL | 低電平輸出電壓 (OUT) | IN+ = 低電平，IN- = 高電平；IOUT = 20mA | 3 | 7 | mV | |
| 短路鉗位 | ||||||
| VCLP-OUT | 鉗位電壓 (VOUT - VCC2) | IN+ = 高電平、IN- = 低電平、tCLAMP = 10μs、IOUT = 500mA | 1 | 1.3 | V | |
| VCLP-OUT | 鉗位電壓 (VEE2 - VOUT) | IN+ = 低電平、IN- = 高電平、tCLAMP = 10μs、IOUT = -500mA | 1.5 | V | ||
| VCLP-OUT | 鉗位電壓 (VEE2 - VOUT) | IN+ = 低電平、IN- = 高電平、tCLAMP = 10μs、IOUT = -20mA | 0.9 | 1 | V | |
| 米勒鉗位 | ||||||
| VCLAMP | 低電平鉗位電壓 | ICLAMP = 20mA | 7 | 13 | mV | |
| ICLAMP | 鉗位低電平電流 | VCLAMP = VEE2 + 15V | 5 | 10 | A | |
| ICLAMP(L) | 低輸出電壓的鉗位低電平電流 | VCLAMP = VEE2 + 2V | 5 | 10 | A | |
| VCLAMP-TH | 鉗位閾值電壓 | 2.1 | 2.3 | V | ||
| 有源下拉 | ||||||
| VOUTSD | OUT 上的有源下拉電壓 | IOUT = 0.1 x IOUT(typ)，VCC2 = 開路 | 1.8 | 2.5 | V | |