SLLSFV1 March 2025 MCF8329A-Q1
PRODUCTION DATA
- 1
- 1 Features
- 2 Applications
- 3 Description
- 4 Pin Configuration and Functions
- 5 Specifications
-
6 Detailed Description
- 6.1 Overview
- 6.2 Functional Block Diagram
- 6.3
Feature Description
- 6.3.1 Three Phase BLDC Gate Drivers
- 6.3.2 Gate Drive Architecture
- 6.3.3 AVDD Linear Voltage Regulator
- 6.3.4 Low-Side Current Sense Amplifier
- 6.3.5 Device Interface Modes
- 6.3.6 Motor Control Input Options
- 6.3.7 Bootstrap Capacitor Initial Charging
- 6.3.8 Starting the Motor Under Different Initial Conditions
- 6.3.9 Motor Start Sequence (MSS)
- 6.3.10 Closed Loop Operation
- 6.3.11 Maximum Torque Per Ampere (MTPA) Control
- 6.3.12 Flux Weakening Control
- 6.3.13 Motor Parameters
- 6.3.14 Motor Parameter Extraction Tool (MPET)
- 6.3.15 Anti-Voltage Surge (AVS)
- 6.3.16 Active Braking
- 6.3.17 Output PWM Switching Frequency
- 6.3.18 Dead Time Compensation
- 6.3.19 Voltage Sense Scaling
- 6.3.20 Motor Stop Options
- 6.3.21 FG Configuration
- 6.3.22 DC Bus Current Limit
- 6.3.23
Protections
- 6.3.23.1 PVDD Supply Undervoltage Lockout (PVDD_UV)
- 6.3.23.2 AVDD Power on Reset (AVDD_POR)
- 6.3.23.3 GVDD Undervoltage Lockout (GVDD_UV)
- 6.3.23.4 BST Undervoltage Lockout (BST_UV)
- 6.3.23.5 MOSFET VDS Overcurrent Protection (VDS_OCP)
- 6.3.23.6 VSENSE Overcurrent Protection (SEN_OCP)
- 6.3.23.7 Thermal Shutdown (OTSD)
- 6.3.23.8 Hardware Lock Detection Current Limit (HW_LOCK_ILIMIT)
- 6.3.23.9 Lock Detection Current Limit (LOCK_ILIMIT)
- 6.3.23.10 Motor Lock (MTR_LCK)
- 6.3.23.11 Motor Lock Detection
- 6.3.23.12 MPET Faults
- 6.3.23.13 IPD Faults
- 6.4 Device Functional Modes
- 6.5 External Interface
- 6.6 EEPROM access and I2C interface
- 7 EEPROM (Non-Volatile) Register Map
- 8 RAM (Volatile) Register Map
- 9 Application and Implementation
- 10Device and Documentation Support
- 11Revision History
- 12Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- RRY|32
散熱焊盤機械數據 (封裝 | 引腳)
- RRY|32
訂購信息
6.3.6.5.1 Linear Control Profiles
Note: For all three profiles
(linear, step, forward/reverse),
- When MCF8329A-Q1 is configured as a sleep device, a zero input reference (0-V in analog mode, 0% duty in PWM mode, DIGITAL_SPEED_CTRL = 0b in I2C mode or 0-Hz in frequency mode) will stop the motor.
- When MCF8329A-Q1 is configured as a standby device, a zero input command will result in motor operating at reference level (speed, power, current or voltage) set by REF_OFF1.
Figure 6-8 Linear Control
ProfilesLinear control profiles can be configured by setting REF_PROFILE_CONFIG to 01b. Linear profiles feature input control references which change linearly between REF_CLAMP1 and REF_CLAMP2 with different slopes which can be set by configuring DUTY_x and REF_x combination.
- DUTY_OFF1 configures the duty command below which the reference will be REF_OFF1.
- DUTY_OFF1 and DUTY_ON1 configures a hysteresis around reference control input REF_CLAMP1 and REF_OFF1 as shown in Figure 6-8.
- DUTY_CLAMP1 configures the duty command till which reference will be constant with a value REF_CLAMP1. DUTY_CLAMP1 can be placed anywhere between DUTY_OFF1 and DUTY_A.
- DUTY_A configures the duty command for reference REF_A. The reference changes from REF_CLAMP1 to REF_A linearly between DUTY_CLAMP1 and DUTY_A. DUTY_A to DUTY_E has to be in the same order as shown in Figure 6-8.
- DUTY_B configures the duty command for reference REF_B. The reference changes linearly between DUTY_A and DUTY_B.
- DUTY_C configures the duty command for reference REF_C. The reference changes linearly between DUTY_B and DUTY_C.
- DUTY_D configures the duty command for reference REF_D. The reference changes linearly between DUTY_C and DUTY_D.
- DUTY_E configures the duty command for reference REF_E. The reference changes linearly between DUTY_D and DUTY_E.
- DUTY_CLAMP2 configures the duty command above which the reference will be constant at REF_CLAMP2. REF_CLAMP2 configures this constant reference between DUTY_CLAMP2 and DUTY_OFF2 . The reference changes linearly between DUTY_E and DUTY_CLAMP2. DUTY_CLAMP2 can be placed anywhere between DUTY_E and DUTY_OFF2.
- DUTY_OFF2 and DUTY_ON2 configures a hysteresis around reference control input REF_CLAMP2 and REF_OFF2 as shown in Figure 6-8.
- DUTY_OFF2 configures the duty command above which the reference will change from REF_CLAMP2 to REF_OFF2.