4 修訂歷史記錄

Changes from E Revision (April 2018) to F Revision

• 將“SN75DP159 的工作溫度范圍為 –40°C 至 85°C”更改為“SN65DP159 的工作溫度范圍為 –40°C 至 85°C”（說明 （續））Go
• 將“SN65DP159 的工作溫度范圍為 0°C 至 85°C”更改為“SN75DP159 的工作溫度范圍為 0°C 至 85°C”（說明 （續））Go

Changes from D Revision (June 2017) to E Revision

• Changed the pinout images appearance in the Pin Configuration and Functions sectionGo

Changes from C Revision (July 2016) to D Revision

• 將標題從“SNx5DP159 6-Gbps DP++ 到 HDMI 重定時器”更改為“SNx5DP159 6-Gbps 交流耦合 TMDS™ 到 HDMI™ 電平轉換器重定時器”Go
• 更改了特性列表Go
• 更改了應用 列表Go
• V_SADJ: Added Note: "Best transmit eye ..", added MIN and MAx values in the Recommended Operating Conditions table Go
• Changed the description of t_d1 in Table 1Go
• Changed read procedures in the I²C Control Behavior sectionGo
• Added paragraph: "DP159 is designed..." to the Application and Implementation sectionGo
• Added 2 paragraphs to the Application Information sectionGo
• Added line item "Adding pre-emphasis will improve..." to the Detailed Design Procedure sectionGo

Changes from B Revision (Arpil 2016) to C Revision

• Recommended Operating Conditions, Changed the CONTROL PINS sectionGo
• Changed the AUX, DDC, and I2C Electrical Characteristics tableGo
• Added text to Figure 31 Note: "The SCL_SRC and SDA_SRC pins must be pulled to ground."Go

Changes from A Revision (July 2015) to B Revision

• Added "Low-level input voltage at OE" to V_IL in the Recommended Operating Conditions tableGo
• Added OE to V_IH "High-level input voltage" in the Recommended Operating Conditions tableGo
• Changed Figure 22Go
• Deleted the VDD_ramp and VCC_ramp MIN values in Table 1Go
• Changed text "through the I²C interface" To: "through the I²C access on the DDC interface" in DDC Functional DescriptionGo
• Changed the HDMI and DVI value for 1Ah Table 3Go
• Added Note to 11–400-kbps in Table 7Go
• Changed the note in the DEV_FUNC_MODE section of Table 7Go
• Changed Note in the DDC_TRAIN_SET section of Table 8Go

Changes from * Revision (July 2015) to A Revision

• 將器件狀態從“產品預覽”更新為“生產數據”Go
• 更新了典型電源數Go
• 刪除了備用電源數Go
• 將“預覽”更改為“生產數據”Go
• Replaced SIG_EN with NC in pinout drawing and Pin Functions tableGo
• Removed lane swap from description of SWAP/POL = H Go
• Updated swing data Go
• Changed DDC link into its pin names between SNK and SRC and updated min value Go
• Added new line for SCL_SNK, SDA_SNKGo
• Removed standby power and standby current rows and updated active power and current numbers Go
• Changed term control to no source termination Go
• Increased I_LEAK max value from 10 µA to 45 µAGo
• Updated redriver mode max jitter value Go
• Clarified polarity swap to input signals Go
• Added more information on compliance in redriver mode Go
• Added note to DDC Functional Description section describing DDC snoop function Go
• Removed bit 4 SIG_EN and made reserved Go
• Removed SIG_EN Pin and added Note 1 for DDC Snoop Go
• Updated schematic to replace SIG_EN pin with NC Go
• Updated VID swing Go
• Changed Title to better match table. Removed Standby and redundant rowsGo
• Updated drawing with pin 17 changed to NC Go