ZHCSI64E February 2019 – August 2021 TLV9101 , TLV9102 , TLV9104
PRODUCTION DATA
| 參數 | 測試條件 | 最小值 | 典型值 | 最大值 | 單位 | ||
|---|---|---|---|---|---|---|---|
| 失調電壓 | |||||||
| VOS | 輸入失調電壓 | VCM = V– | ±0.3 | ±1.5 | mV | ||
| TA = –40°C 至 125°C | ±1.75 | ||||||
| dVOS/dT | 輸入失調電壓漂移 | TA = –40°C 至 125°C | ±0.6 | μV/℃ | |||
| PSRR | 輸入失調電壓與電源間的關系 | VCM = V– | TA = –40°C 至 125°C | ±0.1 | ±0.7 | μV/V | |
| 通道隔離 | f = 0Hz | 5 | μV/V | ||||
| 輸入偏置電流 | |||||||
| IB | 輸入偏置電流 | ±10 | pA | ||||
| IOS | 輸入失調電流 | ±5 | pA | ||||
| 噪聲 | |||||||
| EN | 輸入電壓噪聲 | f = 0.1Hz 至 10Hz | 6 | μVPP | |||
| 1 | μVRMS | ||||||
| eN | 輸入電壓噪聲密度 | f = 1kHz | 30 | nV/√Hz | |||
| f = 10kHz | 28 | ||||||
| iN | 輸入電流噪聲 | f = 1kHz | 2 | fA/√Hz | |||
| 輸入電壓范圍 | |||||||
| VCM | 共模電壓范圍 | (V-)-0.2 | (V+)+0.2 | V | |||
| CMRR | 共模抑制比 | VS = 16V，(V–) – 0.1V < VCM < (V+) – 2V（主輸入對） | TA = –40°C 至 125°C | 90 | 110 | dB | |
| VS = 4V，(V–) – 0.1V < VCM < (V+) – 2V（主輸入對） | 75 | 95 | |||||
| VS = 2.7 – 16V，(V+) – 1V < VCM < (V+) + 0.1V（輔助輸入對） | 80 | ||||||
| (V+) – 2V < VCM < (V+) – 1V | 請參閱典型特性部分中的失調電壓（轉換區域） | ||||||
| 輸入電容 | |||||||
| ZID | 差分 | 100 || 3 | MΩ || pF | ||||
| ZICM | 共模 | 6 || 1 | TΩ || pF | ||||
| 開環增益 | |||||||
| AOL | 開環電壓增益 | VS = 16V，VCM = V– (V–) + 0.1V < VO < (V+) – 0.1V |
TA = –40°C 至 125°C | 115 | 135 | dB | |
| VS = 4V，VCM = V– (V–) + 0.1V < VO < (V+) – 0.1V |
104 | 125 | dB | ||||
| 頻率響應 | |||||||
| GBW | 增益帶寬積 | 1.1 | MHz | ||||
| SR | 壓擺率 | VS = 16V，G = +1，CL = 20pF | 4.5 | V/μs | |||
| tS | 趨穩時間 | 達 0.1%，VS = 16V，VSTEP = 10V，G = +1，CL = 20pF | 4 | μs | |||
| 達 0.1%，VS = 16V，VSTEP = 2V，G = +1，CL = 20pF | 2 | ||||||
| 達 0.01%，VS = 16V，VSTEP = 10V，G = +1，CL = 20pF | 5 | ||||||
| 達 0.01%，VS = 16V，VSTEP = 2V，G = +1，CL = 20pF | 3 | ||||||
| 相位裕度 | G = +1，RL = 10kΩ，CL = 20pF | 60 | ° | ||||
| 過載恢復時間 | VIN × 增益 > VS | 600 | ns | ||||
| THD+N | 總諧波失真 + 噪聲 | VS = 16V，VO = 1 VRMS，G = -1，f = 1kHz | 0.0028% | ||||
| 輸出 | |||||||
| 相對于電源軌的電壓輸出擺幅 | 正負電源軌裕度 | VS = 16V，RL = 空載 | 3 | mV | |||
| VS = 16V，RL = 10kΩ | 45 | 60 | |||||
| VS = 16V，RL = 2kΩ | 200 | 300 | |||||
| VS = 2.7V，RL = 空載 | 1 | ||||||
| VS = 2.7V，RL = 10kΩ | 5 | 20 | |||||
| VS = 2.7V，RL = 2kΩ | 25 | 50 | |||||
| ISC | 短路電流 | ±80 | mA | ||||
| CLOAD | 容性負載驅動 | 請參閱典型特性部分中的小信號過沖與容性負載間的關系 | |||||
| ZO | 開環輸出阻抗 | f=1MHz，IO = 0A | 600 | ? | |||
| 電源 | |||||||
| IQ | 每個放大器的靜態電流 | IO = 0A | 115 | 150 | μA | ||
| TA = –40°C 至 125°C | 160 | ||||||
| 關斷 | |||||||
| IQSD | 每個放大器的靜態電流 | VS = 2.7V 至 16V，所有放大器均為禁用狀態，SHDN = V+ | 20 | 30 | μA | ||
| ZSHDN | 關斷時的輸出阻抗 | VS = 2.7V 至 16V，放大器為禁用狀態，SHDN = V+ | 10 || 12 | GΩ || pF | |||
| VIH | 邏輯高電平閾值電壓（放大器被禁用） | 對于有效輸入高電平，SHDN 引腳電壓應大于最大閾值，但小于或等于 V+ | (V–) + 0.8 | (V–) + 1.1 | V | ||
| VIL | 邏輯低電平閾值電壓（放大器被啟用） | 對于有效輸入低電平，SHDN 引腳電壓應該小于最小閾值，但大于或等于 V– | (V–) + 0.2 | (V–) + 0.8 | V | ||
| tON | 放大器啟用時間(1) | G = +1，VCM = V–，VO = 0.1 × VS/2 | 11 | μs | |||
| tOFF | 放大器禁用時間(1) | VCM = V–，VO = VS/2 | 2.5 | μs | |||
| SHDN 引腳輸入偏置電流（每個引腳） | VS = 2.7V 至 16V，(V–) + 20V ≥ SHDN ≥ (V–) + 0.9V | 500 | nA | ||||
| VS = 2.7V 至 16V，(V–) ≤ SHDN ≤ (V–) + 0.7V | 150 | ||||||