ZHCSH31B August 2017 – February 2018 DRV10987
PRODUCTION DATA.
- 1 特性
- 2 應用
- 3 說明
- 4 修訂歷史記錄
- 5 說明 （續）
- 6 Pin Configuration and Functions
- 7 Specifications
-
8 Detailed Description
- 8.1 Overview
- 8.2 Functional Block Diagram
- 8.3 Feature Description
- 8.4
Device Functional Modes
- 8.4.1 Motor Parameters
- 8.4.2 Starting the Motor Under Different Initial Conditions
- 8.4.3 Motor Start Sequence
- 8.4.4 Align Current
- 8.4.5 Start-Up Current Setting
- 8.4.6 Closed Loop
- 8.4.7 Current Limits
- 8.4.8 Lock Detect and Fault Handling
- 8.4.9 Anti-Voltage Surge Function
- 8.4.10 PWM Output
- 8.4.11 FG Customized Configuration
- 8.4.12
Diagnostics and Visibility
- 8.4.12.1 Motor-Status Readback
- 8.4.12.2 Motor-Speed Readback
- 8.4.12.3 Motor Electrical-Period Readback
- 8.4.12.4 BEMF Constant Readback
- 8.4.12.5 Motor Estimated Position by IPD
- 8.4.12.6 Supply-Voltage Readback
- 8.4.12.7 Speed-Command Readback
- 8.4.12.8 Speed-Command Buffer Readback
- 8.4.12.9 Fault Diagnostics
- 8.5
Register Maps
- 8.5.1 I2C Serial Interface
- 8.5.2 Register Map
- 8.5.3
Register Descriptions
- 8.5.3.1 FaultReg Register (address = 0x00) [reset = 0x00]
- 8.5.3.2 MotorSpeed Register (address = 0x01) [reset = 0x00]
- 8.5.3.3 MotorPeriod Register (address = 0x02) [reset = 0x00]
- 8.5.3.4 MotorKt Register (address = 0x03) [reset = 0x00]
- 8.5.3.5 MotorCurrent Register (address = 0x04) [reset = 0x00]
- 8.5.3.6 IPDPosition–SupplyVoltage Register (address = 0x05) [reset = 0x00]
- 8.5.3.7 SpeedCmd–spdCmdBuffer Register (address = 0x06) [reset = 0x00]
- 8.5.3.8 AnalogInLvl Register (address = 0x07) [reset = 0x00]
- 8.5.3.9 DeviceID–RevisionID Register (address = 0x08) [reset = 0x00]
- 8.5.3.10 Unused Registers (addresses = 0x011 Through 0x2F)
- 8.5.3.11 SpeedCtrl Register (address = 0x30) [reset = 0x00]
- 8.5.3.12 EEPROM Programming1 Register (address = 0x31) [reset = 0x00]
- 8.5.3.13 EEPROM Programming2 Register (address = 0x32) [reset = 0x00]
- 8.5.3.14 EEPROM Programming3 Register (address = 0x33) [reset = 0x00]
- 8.5.3.15 EEPROM Programming4 Register (address = 0x34) [reset = 0x00]
- 8.5.3.16 EEPROM Programming5 Register (address = 0xYY) [reset = 0x00]
- 8.5.3.17 EEPROM Programming6 Register (address = 0x36) [reset = 0x00]
- 8.5.3.18 Unused Registers (addresses = 0x37 Through 0x5F)
- 8.5.3.19 EECTRL Register (address = 0x60) [reset = 0x00]
- 8.5.3.20 Unused Registers (addresses = 0x61 Through 0x8F)
- 8.5.3.21 CONFIG1 Register (address = 0x90) [reset = 0x00]
- 8.5.3.22 CONFIG2 Register (address = 0x91) [reset = 0x00]
- 8.5.3.23 CONFIG3 Register (address = 0x92) [reset = 0x00]
- 8.5.3.24 CONFIG4 Register (address = 0x93) [reset = 0x00]
- 8.5.3.25 CONFIG5 Register (address = 0x94) [reset = 0x00]
- 8.5.3.26 CONFIG6 Register (address = 0x95) [reset = 0x00]
- 8.5.3.27 CONFIG7 Register (address = 0x96) [reset = 0x00]
- 9 Application and Implementation
- 10Power Supply Recommendations
- 11Layout
- 12器件和文檔支持
- 13機械、封裝和可訂購信息
封裝選項
機械數據 (封裝 | 引腳)
- PWP|24
散熱焊盤機械數據 (封裝 | 引腳)
- PWP|24
訂購信息
8.4.8.1 Lock0: Lock-Detection Current Limit Triggered
The lock-detection current-limit function provides a configurable threshold for limiting the current to prevent damage to the system. This is often tripped in the event of a sudden locked-rotor condition. The DRV10987 device continuously monitors the current in the low-side drivers as shown in Figure 34. If the current goes higher than the threshold configured by the HWiLimitThr[2:0] bits, then the DRV10987 device stops driving the motor by placing the output phases into a high-impedance state. The Lock0 bit is set and a lock condition is reported. The device retries after tLOCK_OFF.
Set the lock-detection current limit to a higher value than the software current limit.
Figure 34. Lock-Detection Current Limit