SBAA415 April 2020 PCM6240-Q1 , PCM6260-Q1 , PCM6340-Q1 , PCM6360-Q1
The following I2C scripts sets four devices for Daisy-Chain TDM mode, after devices are reset:
# Key: w NN YY ZZ ==> write to I2C address 0xNN, to register 0xYY, data 0xZZ
# # ==> comment delimiter
#
# I2C programming script for four devices in daisy chain TDM mode
# U4(SDOUT) -> (GPIO1) U3 (SDOUT) -> (GPIO1) U2 (SDOUT) -> (GPIO1) U1 (SDOUT) -> Host Processor
#
#########################################################################
# Power-up Sequence:
# Power up IOVDD and AVDD power supplies keeping SHDNZ pin voltage LOW
# Wait for IOVDD and AVDD power supplies to settle to steady state operating voltage range.
# Release SHDNZ to HIGH.
# Wait for 1ms.
#########################################################################
# Wake-up devices
w 90 02 81 # Wake-up Device U1
w 91 02 81 # Wake-up Device U2
w 92 02 81 # Wake-up Device U3
w 93 02 81 # Wake-up Device U4
d 10 # 10 ms delay
# Program Device A (U1)
w 90 00 00 # Set Device A page register to Page 0
w 90 07 31 # ASI Format TDM with 32-bit word length, default FSYNC and BCLK polarity,
# default TX edge, Hi-Z for unused cycles
w 90 08 A0 # ASI transmit LSB for 1st half cycle, Hi-Z for second half cycle,
# bus keeper always enabled
w 90 09 80 # ASI to daisy chain connection with bus error detection and
# auto resume after bus error recovery
w 90 21 B0 # GPIO1 input as ASI input for daisy chain
w 90 0B 00 # ASI primary output (SDOUT) with CH1 assigned to slot 0
w 90 0C 01 # ASI primary output (SDOUT) with CH2 assigned to slot 1
w 90 0D 02 # ASI primary output (SDOUT) with CH3 assigned to slot 2
w 90 0E 03 # ASI primary output (SDOUT) with CH4 assigned to slot 3
w 90 73 F0 # Enable Ch1-4 of Device A
w 90 74 F0 # Enable Ch1-4 ASI output of Device A
# Program Device B (U2)
w 91 00 00 # Set Device page register to Page 0
w 91 07 31 # ASI Format TDM with 32-bit word length, default FSYNC and BCLK polarity,
# default TX edge, Hi-Z for unused cycles
w 91 08 80 # ASI transmit LSB for 1st half cycle, Hi-Z for second half cycle,
# bus keeper disabled
w 91 09 80 # ASI to daisy chain connection with bus error detection and
# auto resume after bus error recovery
w 91 21 B0 # GPIO1 input as ASI input for daisy chain
w 91 0B 04 # ASI primary output (SDOUT) with CH1 assigned to slot 4
w 91 0C 05 # ASI primary output (SDOUT) with CH2 assigned to slot 5
w 91 0D 06 # ASI primary output (SDOUT) with CH3 assigned to slot 6
w 91 0E 07 # ASI primary output (SDOUT) with CH4 assigned to slot 7
w 91 73 F0 # Enable Ch1-4 of Device B
w 91 74 F0 # Enable Ch1-4 ASI output of Device B
# Program Device C (U3)
w 92 00 00 # Set Device page register to Page 0
w 92 07 31 # ASI Format TDM with 32-bit word length, default FSYNC and BCLK polarity,
# default TX edge, Hi-Z for unused cycles
w 92 08 80 # ASI transmit LSB for 1st half cycle, Hi-Z for second half cycle,
# bus keeper disabled
w 92 09 80 # ASI to daisy chain connection with bus error detection and
# auto resume after bus error recovery
w 92 21 B0 # GPIO1 input as ASI input for daisy chain
w 92 0B 08 # ASI primary output (SDOUT) with CH1 assigned to slot 8
w 92 0C 09 # ASI primary output (SDOUT) with CH2 assigned to slot 9
w 92 0D 0A # ASI primary output (SDOUT) with CH3 assigned to slot 10
w 92 0E 0B # ASI primary output (SDOUT) with CH4 assigned to slot 11
w 92 73 F0 # Enable Ch1-4 of Device C
w 92 74 F0 # Enable Ch1-4 ASI output of Device C
# Program Device D (U4)
w 93 00 00 # Set Device page register to Page 0
w 93 07 31 # ASI Format TDM with 32-bit word length, default FSYNC and BCLK polarity,
# default TX edge, Hi-Z for unused cycles
w 93 08 80 # ASI transmit LSB for 1st half cycle, Hi-Z for second half cycle,
# bus keeper disabled
w 93 0B 0C # ASI primary output (SDOUT) with CH1 assigned to slot 12
w 93 0C 0D # ASI primary output (SDOUT) with CH2 assigned to slot 13
w 93 0D 0E # ASI primary output (SDOUT) with CH3 assigned to slot 14
w 93 0E 0F # ASI primary output (SDOUT) with CH4 assigned to slot 15
w 93 73 F0 # Enable Ch1-4 of Device D
w 93 74 F0 # Enable Ch1-4 ASI output of Device D
# Power-up Devices A, B, C, & D
w 90 75 60 # Power up ADC and PLL of Device A
w 91 75 60 # Power up ADC and PLL of Device B
w 92 75 60 # Power up ADC and PLL of Device C
w 93 75 60 # Power up ADC and PLL of Device D