The UCC27624V driver is capable of delivering 5A of peak current to a switching power device gate (MOSFET, IGBT, SiC MOSFET) for a period of several-hundred nanoseconds at VDD = 12V. High peak current is required to turn ON the device quickly. Then, to turn the device OFF, the driver is required to sink a similar amount of current to ground, which repeats at the operating switching frequency of the power device. The power dissipated in the gate driver device package depends on the following factors:

• Gate charge of the power MOSFET (usually a function of the drive voltage V_GS, which is very close to input bias supply voltage V_DD due to low V_OH drop-out).
• Switching frequency
• External gate resistors

Because UCC27624V features low-quiescent currents and internal logic to eliminate any shoot-through in the output driver stage, their effect on the power dissipation within the gate driver is very small compared to the losses due to switching of the power device.

When a driver device is tested with a discrete capacitive load, calculating the power that is required from the bias supply is fairly simple. The following equation provides an example of the energy that must transfer from the bias supply to charge the capacitor.

Equation 1.

where

• C_LOAD is the load capacitor.
• V_DD is the bias voltage of the driver.

There is an equal amount of energy dissipated when the capacitor is discharged. This leads to a total power loss, as shown in the following equation example.

Equation 2.

where

• f_SW is the switching frequency.

With V_DD = 12V, C_LOAD = 10nF and f_SW = 300kHz, the switching power loss is calculated as follows:

Equation 3.

The switching load presented by a power MOSFET is converted to an equivalent capacitance by examining the gate charge required to switch the device. This gate charge includes the effects of the input capacitance plus the added charge needed to swing the drain voltage of the power device as it switches between the ON and OFF states. Most manufacturers provide specifications that provide the typical and maximum gate charge, in nC, to switch the device under specified conditions. Using the gate charge Q_g, the power that must dissipate when charging a capacitor is determined, which by using the equivalence Q_g = C_LOADV_DD is shown in the following equation.

Equation 4.

Assuming that the UCC27624V device is driving power MOSFET with 60nC of gate charge (Q_g = 60nC at V_DD = 12V) on one output channel, the gate charge related power loss is calculated using the equation below.

Equation 5.

This power P_G is dissipated in the resistive elements of the circuit when the MOSFET turns on or turns off. Half of the total power is dissipated when the load capacitor is charged during turn-on, and the other half is dissipated when the load capacitor is discharged during turn-off. When no external gate resistor is employed between the driver and MOSFET/IGBT, this power is completely dissipated inside the driver package. With the use of external gate resistors, the power dissipation is shared between the internal resistance of driver and external gate resistor in accordance to the ratio of the resistances (more power dissipated in the higher resistance component). Based on this simplified analysis, the driver power dissipation during switching is calculated as follows:

Equation 6.

where

• R_OFF = R_OL
• R_ON = R_OH(effective resistance of pull-up structure)

The above equation is necessary when the external gate resistor is large enough to reduce the peak current of the driver. In addition to the above gate-charge related power dissipation, dissipation in the driver is related to the power associated with the quiescent bias current consumed by the device to bias all internal circuits such as input stage (with pullup and pulldown resistors), enable, and UVLO sections. As shown in the electrical characteristics table, the quiescent current is less than 1mA. The power loss due to DC current consumption of the driver internal circuit can be calculated as below.

Equation 7.

Assuming total internal current consumption to be 0.6mA (typical) at bias voltage of 12V, the DC power loss in the driver is:

Equation 8.

This power loss is insignificant compared to gate charge related power dissipation calculated earlier.

With a 12V supply, the bias current is estimated as follows, with an additional 0.6mA overhead for the quiescent consumption:

Equation 9.

If the gate driver is used with inductive load, then special attention should be paid to the ringing on each pin of the gate driver device. The ringing should not exceed the recommended operating rating of the pin.