中日精品无码一本二本三本,一二三区av电影院,欧美一级牲交大片

ZHCSL68C April 2017 – December 2020 TPS7A84A

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

RGR|20
- MPQF239A

散熱焊盤機械數據 (封裝 | 引腳)

RGR|20
- QFND242E

訂購信息

6.6 Electrical Characteristics: TPS7A8400A

Over operating junction temperature range (T_J = –40°C to +125°C), V_IN = 1.4 V or V_IN = V_OUT(nom) + 0.4 V (whichever is greater), V_BIAS = open, V_OUT(nom) = 0.8 V⁽¹⁾, OUT connected to 50 Ω to GND⁽²⁾, V_EN = 1.1 V, C_IN = 10 μF, C_OUT = 47 μF, C_NR/SS =0nF, without C_FF, and PG pin pulled up to V_IN with 100 kΩ, unless otherwise noted. Typical values are at T_J = 25°C.

PARAMETER			TEST CONDITIONS		MIN	TYP	MAX	UNIT
V_FB	Feedback voltage					0.8		V
V_NR/SS	NR/SS pin voltage					0.8		V
V_OUT	Output voltage	Range	Using the ANY-OUT pins		0.8 – 1.0%		3.95 + 1.0%	V
		Range	Using external resistors⁽³⁾		0.8 – 1.0%		5.15 + 1.0%	V
		Accuracy⁽³⁾ ⁽⁴⁾	0.8 V ≤ V_OUT ≤ 5.15⁽⁵⁾ V, 5 mA ≤ I_OUT ≤ 3 A, over V_IN		–1.0%		1.0%
		Accuracy with BIAS	1.1V ≤ V_IN ≤ 2.2 V, 5 mA ≤ I_OUT ≤ 3 A, 3.0 V ≤ V_BIAS ≤ 6.5 V		–0.75%		0.75%
ΔV_OUT/ ΔV_IN	Line regulation		I_OUT = 5 mA, 1.4 V ≤ V_IN ≤ 6.5 V			0.03		mV/V
ΔV_OUT/ ΔI_OUT	Load regulation		5 mA ≤ I_OUT ≤ 3 A, 3.0 V ≤ V_BIAS ≤ 6.5 V, V_IN= 1.1 V			0.07		mV/A
			5 mA ≤ I_OUT ≤ 3 A			0.08
			5 mA ≤ I_OUT ≤ 3 A, V_OUT = 5.15 V			0.04
V_DO	Dropout voltage		V_IN = 1.4 V, I_OUT = 3 A, V_FB = 0.8 V – 3%			155	250	mV
			V_IN = 5.4 V, I_OUT = 3 A, V_FB = 0.8 V – 3%			225	340
			V_IN = 5.6 V, I_OUT = 3 A, V_FB = 0.8 V – 3%			270	450
			V_IN = 1.1 V, V_BIAS = 5 V, I_OUT = 3 A, V_FB = 0.8 V – 3%			110	180
I_LIM	Output current limit		V_OUT forced at 0.9 × V_OUT(nom), V_IN = V_OUT(nom) + 0.4 V		3.7	4.2	4.7	A
I_SC	Short-circuit current limit		R_LOAD = 20 mΩ, under foldback operation			1.0		A
PSRR	Power-supply ripple rejection		V_IN– V_OUT = 0.4 V, I_OUT = 3 A, C_NR/SS = 100 nF, C_FF = 10 nF, C_OUT = 22 μF	f = 10 kHz, V_OUT= 0.8 V, V_BIAS = 5.0 V		42		dB
				f = 500 kHz, V_OUT = 0.8 V, V_BIAS = 5.0 V		39
				f = 10 kHz, V_OUT = 5.0 V		40
				f = 500 kHz, V_OUT= 5.0 V		25
V_n	Output noise voltage		BW = 10 Hz to 100 kHz, V_IN = 1.1 V, V_OUT = 0.8 V, V_BIAS= 5.0 V, I_OUT = 3 A, C_NR/SS = 100 nF, C_FF = 10 nF, C_OUT = 47 μF \|\| 10μF \|\| 10μF			4.4		μV_RMS
V_n	Output noise voltage		BW = 10 Hz to 100 kHz, V_OUT = 5.0 V, I_OUT = 3 A, C_NR/SS = 100 nF, C_FF = 10 nF, C_OUT = 47 μF \|\| 10μF \|\| 10μF			7.7		μV_RMS
I_GND	GND pin current		V_IN = 6.5 V, I_OUT = 5mA			3	4	mA
			V_IN = 1.4 V, I_OUT = 3A			4.3	5.5	mA
			Shutdown, PG = open, V_IN = 6.5 V, V_EN = 0.5 V			1.2	25	μA
V_IT(PG)	PG pin threshold		For falling V_OUT		82% x V_OUT	88% x V_OUT	93% x V_OUT	V
V_HYS(PG)	PG pin hysteresis		For rising V_OUT			2% x V_OUT		V

(1) V_OUT(nom) is the calculated V_OUT target value from the ANY-OUT in a fixed configuration. In an adjustable configuration, V_OUT(nom) is the expected V_OUT value set by the external feedback resistors.

(2) This 50-Ω load is disconnected when the test conditions specify an I_OUT value.

(3) When the device is connected to external feedback resistors at the FB pin, external resistor tolerances are not included.

(4) The device is not tested under conditions where V_IN > V_OUT + 1.7 V and I_OUT = 3 A, because the power dissipation is higher than the maximum rating of the package.

(5) For V_OUT ≤ 5 V, V_IN = V_OUT + 0.4 V; For V_OUT > 5 V, V_IN = V_OUT + 0.45 V