| SUPPLY VOLTAGE (VIN) |
| VVIN
|
Operating input voltage |
|
2.95 |
|
6 |
V |
| VUVLO
|
Internal under voltage lockout threshold |
No voltage hysteresis, rising and falling |
|
2.6 |
2.8 |
V |
| IQ(vin)
|
Shutdown supply current |
VEN = 0 V, TA = 25°C, 2.95 V ≤ VVIN ≤ 6 V |
|
2 |
5 |
μA |
| Iq
|
Quiescent current |
VVSENSE = 0.9 V, VVIN = 5 V, 25°C,
RT = 400 kΩ |
|
350 |
500 |
μA |
| ENABLE AND UVLO (EN) |
| VTH(en)
|
Enable threshold |
Rising |
1.16 |
1.25 |
1.37 |
V |
| Falling |
|
1.18 |
|
| IEN
|
Input current |
Enable rising threshold + 50 mV |
|
–3.2 |
|
μA |
| Enable falling threshold – 50 mV |
|
–0.65 |
|
| VOLTAGE REFERENCE (VSENSE) |
| VREF
|
Voltage reference |
2.95 V ≤ VVIN ≤ 6 V, –40°C <TJ< 150°C |
0.795 |
0.803 |
0.811 |
V |
| MOSFET |
| RDS(HFET)
|
High-side switch resistance |
(VBOOT – VPH) = 5 V |
|
30 |
60 |
mΩ |
| (VBOOT – VPH) = 2.95 V |
|
44 |
70 |
| RDS(LFET)
|
Low-side switch resistance |
VVIN = 5 V |
|
30 |
60 |
mΩ |
| VVIN = 2.95 V |
|
44 |
70 |
| ERROR AMPLIFIER |
| IIN
|
Input current |
|
|
7 |
|
nA |
| gM(ea)
|
Error amplifier transconductance |
–2 μA < ICOMP< 2 μA, VCOMP = 1 V |
|
225 |
|
μS |
| gm(EA,ss)
|
Error amplifier transconductance during soft-start |
–2 μA < ICOMP< 2 μA, VCOMP = 1 V,
VVSENSE = 0.4 V |
|
70 |
|
μS |
| ICOMP
|
Error amplifier source/sink |
VCOMP = 1 V, 100 mV overdrive |
|
±20 |
|
μA |
| gM
|
COMP to ISWITCH transconductance |
|
|
13 |
|
A/V |
| CURRENT LIMIT
|
| ILIM
|
Current limit threshold |
Instantaneous peak current |
3.7 |
5.5 |
|
A |
| THERMAL SHUTDOWN |
| TSD
|
Thermal Shutdown |
|
|
175 |
|
°C |
| TSD(hyst)
|
Hysteresis |
|
|
15 |
|
°C |
| TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK) |
| fSW
|
Switching frequency range using RT mode |
|
200 |
|
2000 |
kHz |
| fSW
|
Switching frequency |
RRT = 400 kΩ |
400 |
500 |
600 |
kHz |
| fSW
|
Switching frequency range using CLK mode |
|
300 |
|
2000 |
kHz |
| tMIN(CLK)
|
Minimum CLK pulse width |
|
75 |
|
|
ns |
| VRT/CLK
|
RT/CLK voltage |
RRT/CLK = 400 kΩ |
|
0.5 |
|
V |
| VIH(CLK)
|
RT/CLK high threshold |
|
|
1.6 |
2.2 |
V |
| VIL(CLK)
|
RT/CLK low threshold |
|
0.4 |
0.6 |
|
V |
| tDLY
|
RT/CLK falling edge to PH rising edge delay |
fSW = 500 kHz with RRT resistor in series |
|
90 |
|
ns |
| tLOCK(PLL)
|
PLL lock-in time |
fSW = 500 kHz |
|
14 |
|
μs |
| HIGH-SIDE POWER MOSFET (PH) |
| tON(min)
|
Minimum on time |
Measured at 50% points on PH, IOUT = 3 |
|
60 |
|
ns |
Measured at 50% points on PH, VVIN = 5 V,
IOUT = 0 A |
|
110 |
|
| tOFF(min)
|
Minimum off time |
Prior to skipping off pulses,
(VBOOT – VPH) = 2.95 V, IOUT = 3 |
|
60 |
|
ns |
| tRISE
|
Rise time |
VVIN = 5 V |
|
1.5 |
|
V/ns |
| tFALL
|
Fall time |
VVIN = 5 V |
|
1.5 |
|
V/ns |
| BOOT (BOOT) |
| RBOOT
|
BOOT charge resistance |
VVIN = 5 V |
|
16 |
|
Ω |
| VUVLO(Boot)
|
BOOT-PH UVLO |
VVIN = 2.95 V |
|
2.1 |
|
V |
| SOFT-START (SS ) |
| ICHG
|
Charge current |
VSS = 0.4 V |
|
1.8 |
|
μA |
| VSSxREF
|
SS to reference crossover |
98% nominal |
|
0.9 |
|
V |
| VDSCHG(SS)
|
SS discharge voltage (overload) |
VVSENSE = 0 V |
|
20 |
|
μA |
| IDSCHG(SS)
|
SS discharge current (UVLO, EN, thermal fault) |
VVIN = 5 V, VSS = 0.5 V |
|
1.25 |
|
mA |
| POWER GOOD (PWRGD) |
| VTH(PG)
|
VSENSE threshold |
VVSENSE falling (fault) |
|
91% |
|
VREF
|
| VVSENSE rising (good) |
|
93% |
|
| VVSENSE rising (fault) |
|
107% |
|
| VVSENSE falling (Good) |
|
105% |
|
| VHYST(PG)
|
Hysteresis |
VVSENSE falling |
|
2% |
|
| IPH(lkg)
|
Output high leakage |
VVSENSE = VREF, VPWRGD = 5.5 V |
|
2 |
|
nA |
| RPG
|
Power Good on-resistance |
|
|
100 |
|
Ω |
| VOL
|
Low-level output voltage |
IPWRGD = 3.5 mA |
|
0.3 |
|
V |
| VMIN(PG)
|
Minimum input voltage for valid output |
VPWRGD< 0.5 V , IOUT = 100 μA |
|
1.2 |
1.6 |
V |