ZHCSJZ7B june   2019  – february 2023 TPS1HB35-Q1

PRODUCTION DATA  

1. 1 特性
2. 2 應用
3. 3 說明
4. 4 Revision History
5. 5 Device Comparison Table
6. 6 Pin Configuration and Functions
   1. 6.1 Recommended Connections for Unused Pins
7. 7 Specifications
   1. 7.1 Recommended Operating Conditions
   2. 7.2 Electrical Characteristics
   3. 7.3 Absolute Maximum Ratings
   4. 7.4 ESD Ratings
   5. 7.5 Thermal Information
   6. 7.6 SNS Timing Characteristics
   7. 7.7 Switching Characteristics
   8. 7.8 Typical Characteristics
8. 8 Parameter Measurement Information
9. 9 Detailed Description
   1. 9.1 Overview
   2. 9.2 Functional Block Diagram
   3. 9.3 Feature Description
      1. 9.3.1 Protection Mechanisms
         1. 9.3.1.1 Thermal Shutdown
         2. 9.3.1.2 Current Limit
            1. 9.3.1.2.1 Current Limit Foldback
            2. 9.3.1.2.2 Programmable Current Limit
            3. 9.3.1.2.3 Undervoltage Lockout (UVLO)
            4. 9.3.1.2.4 VBB During Short-to-Ground
         3. 9.3.1.3 Voltage Transients
            1. 9.3.1.3.1 Load Dump
            2. 9.3.1.3.2 Driving Inductive Loads
         4. 9.3.1.4 Reverse Battery
         5. 9.3.1.5 Current Limit Behavior
         6. 9.3.1.6 Fault Event – Timing Diagrams
      2. 9.3.2 Diagnostic Mechanisms
         1. 9.3.2.1 VOUT Short-to-Battery and Open-Load
            1. 9.3.2.1.1 Detection With Switch Enabled
            2. 9.3.2.1.2 Detection With Switch Disabled
         2. 9.3.2.2 SNS Output
            1. 9.3.2.2.1 RSNS Value
               1. 9.3.2.2.1.1 High Accuracy Load Current Sense
               2. 9.3.2.2.1.2 SNS Output Filter
         3. 9.3.2.3 Fault Indication and SNS Mux
         4. 9.3.2.4 Resistor Sharing
         5. 9.3.2.5 High-Frequency, Low Duty-Cycle Current Sensing
   4. 9.4 Device Functional Modes
      1. 9.4.1 Off
      2. 9.4.2 Standby
      3. 9.4.3 Diagnostic
      4. 9.4.4 Standby Delay
      5. 9.4.5 Active
      6. 9.4.6 Fault
10. 10Application and Implementation
    1. 10.1 Application Information
       1. 10.1.1 Ground Protection Network
       2. 10.1.2 Interface With Microcontroller
       3. 10.1.3 I/O Protection
       4. 10.1.4 Inverse Current
       5. 10.1.5 Loss of GND
       6. 10.1.6 Automotive Standards
          1. 10.1.6.1 ISO7637-2
          2. 10.1.6.2 AEC-Q100-012 Short Circuit Reliability
       7. 10.1.7 Thermal Information
    2. 10.2 Typical Application
       1. 10.2.1 Design Requirements
       2. 10.2.2 Detailed Design Procedure
          1. 10.2.2.1 Thermal Considerations
          2. 10.2.2.2 RILIM Calculation
          3. 10.2.2.3 Diagnostics
             1. 10.2.2.3.1 Selecting the RISNS Value
    3. 10.3 Typical Application
       1. 10.3.1 Design Requirements
       2. 10.3.2 Detailed Design Procedure
       3. 10.3.3 Application Curves
    4. 10.4 Power Supply Recommendations
    5. 10.5 Layout
       1. 10.5.1 Layout Guidelines
       2. 10.5.2 Layout Example
11. 11Device and Documentation Support
    1. 11.1 Documentation Support
       1. 11.1.1 Related Documentation
    2. 11.2 接收文檔更新通知
    3. 11.3 支持資源
    4. 11.4 Trademarks
    5. 11.5 靜電放電警告
    6. 11.6 術語表
12. 12Mechanical, Packaging, and Orderable Information