ZHCSPQ7A december 2022 – april 2023 MCT8315A
PRODUCTION DATA
- 1
- 1 特性
- 2 應用
- 3 說明
- 4 Revision History
- 5 Pin Configuration and Functions
- 6 Specifications
-
7 Detailed Description
- 7.1 Overview
- 7.2 Functional Block Diagram
- 7.3
Feature Description
- 7.3.1 Output Stage
- 7.3.2 Device Interface
- 7.3.3 Step-Down Mixed-Mode Buck Regulator
- 7.3.4 AVDD Linear Voltage Regulator
- 7.3.5 Charge Pump
- 7.3.6 Slew Rate Control
- 7.3.7 Cross Conduction (Dead Time)
- 7.3.8 Speed Control
- 7.3.9 Starting the Motor Under Different Initial Conditions
- 7.3.10 Motor Start Sequence (MSS)
- 7.3.11 Closed Loop Operation
- 7.3.12 Speed Loop
- 7.3.13 Input Power Regulation
- 7.3.14 Anti-Voltage Surge (AVS)
- 7.3.15 Output PWM Switching Frequency
- 7.3.16 Fast Start-up (< 50 ms)
- 7.3.17 Fast Deceleration
- 7.3.18 Active Demagnetization
- 7.3.19 Motor Stop Options
- 7.3.20 FG Configuration
- 7.3.21
Protections
- 7.3.21.1 VM Supply Undervoltage Lockout
- 7.3.21.2 AVDD Undervoltage Lockout (AVDD_UV)
- 7.3.21.3 BUCK Undervoltage Lockout (BUCK_UV)
- 7.3.21.4 VCP Charge Pump Undervoltage Lockout (CPUV)
- 7.3.21.5 Overvoltage Protection (OVP)
- 7.3.21.6 Overcurrent Protection (OCP)
- 7.3.21.7 Buck Overcurrent Protection
- 7.3.21.8
Cycle-by-Cycle (CBC) Current Limit (CBC_ILIMIT)
- 7.3.21.8.1 CBC_ILIMIT Automatic Recovery next PWM Cycle (CBC_ILIMIT_MODE = 000xb)
- 7.3.21.8.2 CBC_ILIMIT Automatic Recovery Threshold Based (CBC_ILIMIT_MODE = 001xb)
- 7.3.21.8.3 CBC_ILIMIT Automatic Recovery after 'n' PWM Cycles (CBC_ILIMIT_MODE = 010xb)
- 7.3.21.8.4 CBC_ILIMIT Report Only (CBC_ILIMIT_MODE = 0110b)
- 7.3.21.8.5 CBC_ILIMIT Disabled (CBC_ILIMIT_MODE = 0111b or 1xxxb)
- 7.3.21.9 Lock Detection Current Limit (LOCK_ILIMIT)
- 7.3.21.10 Thermal Warning (OTW)
- 7.3.21.11 Thermal Shutdown (TSD)
- 7.3.21.12 Motor Lock (MTR_LCK)
- 7.3.21.13 Motor Lock Detection
- 7.3.21.14 SW VM Undervoltage Protection
- 7.3.21.15 SW VM Overvoltage Protection
- 7.3.21.16 IPD Faults
- 7.4 Device Functional Modes
- 7.5 External Interface
- 7.6 EEPROM access and I2C interface
- 7.7 EEPROM (Non-Volatile) Register Map
- 7.8 RAM (Volatile) Register Map
- 8 Application and Implementation
- 9 Power Supply Recommendations
- 10Layout
- 11Device and Documentation Support
- 12Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- RGF|40
散熱焊盤機械數據 (封裝 | 引腳)
- RGF|40
訂購信息
7.3.11.2 Variable Commutation
Variable commutation can be configured by setting COMM_CONTROL to 01b. 120o commutation may result in acoustic noise due to the long Hi-Z period causing some torque ripple in the motor. In order to reduce this torque ripple and acoustic noise, the MCT8315A uses variable commutation to reduce the phase current ripple at commutation by extending 120o driving time and gradually decreasing duty cycle prior to entering Hi-Z state. In this mode, the phase is Hi-Z between 30o and 60o and this window size is dynamically adjusted based on speed. A smaller window size will typically give better acoustic performance. Figure 7-31 shows 150o commutation with 30o window size.
Figure 7-31 150o
commutationDifferent modulation modes are supported only with 120o commutation; variable commutation uses mixed modulation mode only.