ZHCSSV1 august 2023 MCF8316C-Q1
PRODUCTION DATA
- 1
- 1 特性
- 2 應用
- 3 說明
- 4 Revision History
- 5 Pin Configuration and Functions
- 6 Specifications
-
7 Detailed Description
- 7.1 Overview
- 7.2 Functional Block Diagram
- 7.3
Feature Description
- 7.3.1 Output Stage
- 7.3.2 Device Interface
- 7.3.3 Step-Down Mixed-Mode Buck Regulator
- 7.3.4 AVDD Linear Voltage Regulator
- 7.3.5 Charge Pump
- 7.3.6 Slew Rate Control
- 7.3.7 Cross Conduction (Dead Time)
- 7.3.8 Motor Control Input Sources
- 7.3.9 Starting the Motor Under Different Initial Conditions
- 7.3.10 Motor Start Sequence (MSS)
- 7.3.11 Closed Loop Operation
- 7.3.12 Motor Parameters
- 7.3.13 Motor Parameter Extraction Tool (MPET)
- 7.3.14 Anti-Voltage Surge (AVS)
- 7.3.15 Active Braking
- 7.3.16 Output PWM Switching Frequency
- 7.3.17 PWM Modulation Schemes
- 7.3.18 Dead Time Compensation
- 7.3.19 Motor Stop Options
- 7.3.20 FG Configuration
- 7.3.21 DC Bus Current Limit
- 7.3.22
Protections
- 7.3.22.1 VM Supply Undervoltage Lockout
- 7.3.22.2 AVDD Undervoltage Lockout (AVDD_UV)
- 7.3.22.3 BUCK Under Voltage Lockout (BUCK_UV)
- 7.3.22.4 VCP Charge Pump Undervoltage Lockout (CPUV)
- 7.3.22.5 Overvoltage Protection (OVP)
- 7.3.22.6 Overcurrent Protection (OCP)
- 7.3.22.7 Buck Overcurrent Protection
- 7.3.22.8 Hardware Lock Detection Current Limit (HW_LOCK_ILIMIT)
- 7.3.22.9 Lock Detection Current Limit (LOCK_ILIMIT)
- 7.3.22.10 FET Thermal Warning (OTW)
- 7.3.22.11 FET Thermal Shutdown (TSD_FET)
- 7.3.22.12 Motor Lock (MTR_LCK)
- 7.3.22.13 Motor Lock Detection
- 7.3.22.14 MPET Faults
- 7.3.22.15 IPD Faults
- 7.4 Device Functional Modes
- 7.5 External Interface
- 7.6 EEPROM access and I2C interface
- 7.7 EEPROM (Non-Volatile) Register Map
- 7.8 RAM (Volatile) Register Map
- 8 Application and Implementation
- 9 Power Supply Recommendations
- 10Layout
- 11Device and Documentation Support
- 12Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- RGF|40
散熱焊盤機械數據 (封裝 | 引腳)
- RGF|40
訂購信息
7.3.8.5.2 Staircase Speed Profile
Figure 7-19 Staircase Reference ProfileStaircase control profiles can be configured by setting REF_PROFILE_CONFIG to 10b. Staircase profiles feature input control reference changes in steps between REF_CLAMP1 and REF_CLAMP2, by configuring DUTY_x and REF_x.
- DUTY_OFF1 configures the duty command below which the reference will be REF_OFF1.
- DUTY_OFF1 and DUTY_ON1 configure a hysteresis between reference levels REF_CLAMP1 and REF_OFF1 as shown in Figure 7-19.
- DUTY_CLAMP1 configures the duty command till which reference will be constant. REF_CLAMP1 configures this constant reference between DUTY_OFF1 and DUTY_CLAMP1. DUTY_CLAMP1 can be placed anywhere between DUTY_ON1 and DUTY_A.
- DUTY_A configures the duty command for reference REF_A. There is a step change in reference from REF_CLAMP1 to REF_A at DUTY_CLAMP1. DUTY_A to DUTY_E has to be in the same order as shown in Figure 7-19.
- DUTY_B configures the duty command for reference REF_B. There is a step change in reference from REF_A to REF_B at DUTY_A.
- DUTY_C configures the duty command for reference REF_C. There is a step change in reference from REF_B to REF_C at DUTY_B.
- DUTY_D configures the duty command for reference REF_D. There is a step change in reference from REF_C to REF_D at DUTY_C.
- DUTY_E configures the duty command for reference REF_E. There is a step change in reference from REF_D to REF_E at DUTY_D.
- DUTY_CLAMP2 configures the duty command above which the reference will be constant at REF_CLAMP2. REF_CLAMP2 configures this constant reference between DUTY_CLAMP2 and DUTY_OFF2. There is a step change in reference from REF_E to REF_CLAMP2 at DUTY_E. DUTY_CLAMP2 can be placed anywhere between DUTY_E and DUTY_ON2.
- DUTY_OFF2 and DUTY_ON2 configure a hysteresis between reference levels REF_CLAMP2 and REF_OFF2 as shown in Figure 7-19.
- DUTY_OFF2 configures the duty command above which the reference will change from REF_CLAMP2 to REF_OFF2.