女人被狂躁c点高潮喷小说霍水,久久国产欧美成人网站,国语自产拍在线观看hd

ZHCSH86B December 2017 – February 2019 LMH5401-SP

PRODUCTION DATA.

封裝選項

機械數據 (封裝 | 引腳)

FFK|14
- MCCC005A

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

7.5 Electrical Characteristics: V_S = 5 V

The specifications shown below correspond to the respectively identified subgroup temperature (see Table 1), unless otherwise noted. VS+ = 5 V; VS– = 0 V; V_CM = 2.5 V; RL_total = 200-Ω differential⁽³⁾; Gp = 8 dB (Gv = 17 dB); single-ended input, differential output, and R_S = 50 Ω (unless otherwise noted)⁽¹⁾.

PARAMETER		TEST CONDITIONS	SUBGROUP⁽⁴⁾	MIN	TYP	MAX	UNIT
AC PERFORMANCE
GBP	Gain bandwidth product	Gp = 8 dB			6.5		GHz
SSBW	Small-signal, –3-dB bandwidth	V_L = 100 mV_PP			4.2		GHz
LSBW	Large-signal, –3-dB bandwidth	V_L = 1.0 V_PP			4		GHz
	Bandwidth for ±0.5-dB flatness	V_L = 1.0 V_PP			2.9		GHz
SR	Slew rate	2-V step			17500		V/µs
	Rise and fall time	1-V step, 10% to 90%			80		ps
	Overdrive recovery	Overdrive = ±0.5 V			300		ps
	Output balance error	f = 1 GHz			–47		dBc
z_o	Output impedance	At dc, differential	[1, 2, 3]	13	20	25	Ω
	0.1% settling time	2 V, R_L = 200 Ω			1		ns
HD2	Second-order harmonic distortion	f = 100 MHz, V_L = 1 V_PP			–91		dBc
		f = 200 MHz, V_L = 1 V_PP			–86
		f = 500 MHz, V_L = 1 V_PP			–80
		f = 1 GHz, V_L = 1 V_PP			–53
		f = 2 GHz, V_L = 1 V_PP			–68
HD3	Third-order harmonic distortion	f = 100 MHz, V_L = 1 V_PP			–95		dBc
		f = 200 MHz, V_L = 1 V_PP			–85
		f = 500 MHz, V_L = 1 V_PP			–80
		f = 1 GHz, V_L = 1 V_PP			–70
		f = 2 GHz, V_L = 1 V_PP			–56
IMD2	Second-order intermodulation	f = 500 MHz, V_L = 1 V_PP per tone			–90		dBc
		f = 1 GHz, V_L = 1 V_PP per tone			–80
		f = 2 GHz, V_L = 1 V_PP per tone			–64
OIP2	Second-order output intercept point	f = 500 MHz, VL = 1 V_PP, matched load			91		dBm
OIP2	Second-order output intercept point	f = 1000 MHz, VL = 1 V_PP, matched load			80		dBm
IMD3	Third-order intermodulation	f = 500 MHz, V_L = 0.25 V_PP per tone			–79		dBc
		f = 1 GHz, V_L = 0.25 V_PP per tone			–61
		f = 2 GHz, V_L = 0.25 V_PP per tone			–42
OIP3	Third-order output intercept point	f = 500 MHz, VL = 1 V_PP, unmatched load			47.7		dBm
OIP3	Third-order output intercept point	f = 1000 MHz, VL = 1 V_PP, unmatched load			37.5		dBm
NOISE PERFORMANCE
e_n	Input voltage noise density				1.25		nV/√Hz
i_n	Input noise current				3.5		pA/√Hz
NF	Noise figure	R_S = 50 Ω, SE-DE, 200 MHz See Figure 57			9.6		dB
INPUT
V_IO	Input offset voltage		[1, 2, 3]		±0.5	±5	mV
I_IB	Input bias current		[1, 2, 3]		70	150	µA
I_IO	Input offset current		[1, 2, 3]		±1	±20	µA
	Differential resistance	Open-loop			4600		Ω
V_ICL	Input common-mode low voltage		[1, 2, 3]		VS–	(VS–) + 0.41	V
V_ICH	Input common-mode high voltage		[1, 2, 3]	(VS+) – 1.41	(VS+) – 1.2		V
CMRR	Common-mode rejection ratio	Differential, 1-V_PP input shift, dc			72		dBc
OUTPUT
V_OCRH	Output voltage range, high	Measured single-ended	[1, 2, 3]	(VS+) – 1.3	(VS+) – 1.1		V
V_OCRL	Output voltage range, low	Measured single-ended	[1, 2, 3]	(VS–) + 1.3	(VS–) + 1.1		V
V_OD	Differential output voltage swing	Differential			5.8		V_PP
I_OD	Differential output current	V_O = 0 V⁽²⁾	[1, 2, 3]	40	50		mA
POWER SUPPLY
V_S	Supply voltage		[1, 2, 3]	3.15		5.25	V
PSRR	Power-supply rejection ratio	VS–	[1, 2, 3]		–80	–44	dB
PSRR	Power-supply rejection ratio	VS+	[1, 2, 3]		–82	–48	dB
I_Q	Quiescent current	PD = 0	[1, 2, 3]	46	60	78	mA
I_Q	Quiescent current	PD = 1	[1, 2, 3]	1	3	6	mA
OUTPUT COMMON-MODE CONTROL PIN (V_CM)
SSBW	Small-signal bandwidth	V_OCM = 100 mV_PP			1.2		GHz
	V_CM slew rate	V_OCM = 500 mV_PP			2900		V/µs
	V_CM voltage range low	Differential gain shift < 1 dB	[1, 2, 3]		(VS–) + 1.4	(VS–) + 2	V
	V_CM voltage range high	Differential gain shift < 1 dB	[1, 2, 3]	(VS+) – 2	(VS+) – 1.4		V
	V_CM gain	V_CM = 0 V	[1, 2, 3]	0.98	1.0	1.01	V/V
	V_OCM output common-mode offset from V_CM input voltage	V_CM = 0 V			–27		mV
V_OCM	Common-mode offset voltage	Output-referred			0.4		mV
POWER DOWN (PD PIN)
V_T	Enable or disable voltage threshold	Device powers on below 0.8 V, device powers down above 1.2 V	[1, 2, 3]	0.9	1.1	1.2	V
	Power-down quiescent current		[1, 2, 3]	1	3	6	mA
	PD bias current	PD = 2.5 V	[1, 2, 3]		10	±100	µA
	Turn-on time delay	Time to V_O = 90% of final value			10		ns
	Turn-off time delay	Time to V_O = 10% of original value			10		ns

(1) The input resistance and corresponding gain are obtained with the external resistance added.

(2) This test shorts the outputs to ground (mid supply) then sources or sinks 60 mA and measures the deviation from the initial condition.

(3) Please see the Output Reference Nodes and Gain Nomenclature section.

(4) For subgroup definitions, please see Table 1.

封裝選項

機械數據 (封裝 | 引腳)

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

7.5 Electrical Characteristics: VS = 5 V

7.5 Electrical Characteristics: V_S = 5 V