4 修訂歷史記錄

Changes from F Revision (December 2017) to G Revision

• Added timing information for entering and exiting sleep mode and standby modeGo
• Added BEMF COMPARATOR hysteresis specificationGo
• Updated Start the Motor Under Different Initial Conditions figureGo
• Changed the default value for register address 0x27 from 0xFC to 0xF4 in the Default EEPROM Value tableGo
• Deleted the "TI recommends..." sentence from the description for address 0x27, bit 3Go
• Added constraints to recommended external inductorGo

Changes from E Revision (May 2017) to F Revision

• Added the internal SPEED pin pulldown resistance to ground parameter to the Electrical Characteristics tableGo
• Changed the Step-Down Regulator sectionGo
• Updated the Motor Phase Resistance sectionGo
• Deleted the Inductive AVS Function sectionGo
• Changed the default value for register address 0x29 from 0xB7 to 0xB9 in the Default EEPROM Value tableGo
• Added application information for the sleep mode device Go

Changes from D Revision (May 2017) to E Revision

• Changed pin numbering in the Pin Functions table Go

Changes from C Revision (May 2016) to D Revision

• 在數據表標題和器件信息表中添加了 DRV10983Z 器件型號Go
• Added DRV10983Z part numberGo
• Corrected the link to the DRV10983 and DRV10975 Tuning GuideGo
• Added text to the PWM Output sectionGo
• Changed Figure 37Go
• Changed "FGOLSet[1:0]" to "FGOLsel[1:0]" in Register Map address 0x2BGo
• Added recommended minimum dead time to SysOpt7 registerGo
• Added External Components table Go
• Changed the link to the DRV10983 and DRV10975 Tuning GuideGo
• Changed the layout exampleGo

Changes from B Revision (February 2015) to C Revision

• Added "phase to phase" clarification for overcurrent protectionGo
• Added more accurate description to clarify overcurrent protection operationGo

Changes from A Revision (October 2014) to B Revision

• 更新了數據表以包含 DRV10983Z 睡眠型號Go

Changes from * Revision (July 2014) to A Revision

• 更新了輸入電壓范圍：8V 至 28VGo
• 刪除了 DRV10983Z 睡眠型號部分并更新了待機模式電源電流Go
• Updated pin information for SW, SWGND, VREG, SDA, FG, and VCC pinsGo
• Added DIR, SW, and VREG pins to Absolute Maximum RatingsGo
• Updated max supply voltage and voltage range ratings for VCC and U, V, W in Recommended Operating ConditionsGo
• changed Functional Block DiagramGo
• Changed "hardware current limit" to "lock detection current limit" and "software current" to "acceleration current limit" throughout data sheetGo
• Updated max value for open to closed loop threshold Go
• Corrected description to "velocity constant of the motor" for Equation 2Go
• Corrected register name in Start-Up Current SettingGo
• Updated Equation 3Go
• Updated Figure 20Go
• Updated caption name for Figure 24Go
• Corrected max speed command setting for SpdCtrl[8:0] Go
• Updated register description for status register. Go
• Updated the data in the examples for MotorSpeed1 and MotorPeriod1 Go
• Updated IPDPosition description in Register MapGo
• Increased max motor voltage for Recommended Application Range Go
• Updated graph callout for Figure 41Go