4 Revision History
Changes from E Revision (September 2014) to F Revision
-
Deleted Device Comparison Table; same information in POA Go
-
Added Support for 105ºC thermal pad temperature Go
-
Changed Handing Ratings to ESD Ratings (format update). Go
-
Added added PCB temperature in Recommended Operating ConditionsGo
-
Added VOH specification for TPCB≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 2.375 V to 2.625 VGo
-
Added VOL specification for TPCB≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 2.375 V to 2.625 VGo
-
Added IEE specification for TPCB ≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 2.375 V to 2.625 VGo
-
Added ICC specification for TPCB ≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 2.375 V to 2.625 V Go
-
Added VOH specification for TPCB≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 3 V to 3.6 VGo
-
Added VOL specification for TPCB≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 3 V to 3.6 VGo
-
Added IEE specification for TPCB ≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 3 V to 3.6 V Go
-
Added ICC specification for TPCB ≤ 105ºC in Electrical Characteristics: LVPECL Output, at VCC = 3 V to 3.6 VGo
-
Added Thermal Considerations section Go
Changes from D Revision (June 2014) to E Revision
-
Changed JEDEC symbol from θJA to RθJAGo
-
Added NOTE at the beginning of Applications and Implementation section.Go
Changes from C Revision (August 2011) to D Revision
-
Added data sheet flow and layout to conform with new TI standards. Added the following sections: Application and Implementation; Power Supply Recommendations; Layout; Device and Documentation Support; Mechanical, Packaging, and Ordering InformationGo
-
Added fIN = 125 MHz, 312.5 MHz for VOUT, DIFF, PPGo
-
Added Typical values, Max values, and footnotes for 122.88 MHz, 156.25 MHz, and 312.5 MHz test conditions corresponding to Random Additive Jitter in Electrical Characteristics: LVPECL Output, at VCC = 2.375 V to 2.625 VGo
-
Added Typical values, Max values, and footnotes for 122.88 MHz, 156.25 MHz, and 312.5 MHz test conditions corresponding to Random Additive Jitter in Electrical Characteristics: LVPECL Output, at VCC = 3.0 V to 3.6 VGo
Changes from B Revision (May, 2010) to C Revision
-
Revised description of pin 8Go
-
Corrected VIL parameter description in Electrical Characteristics table for LVCMOS inputsGo
-
Added footnote (2) to Electrical Characteristics table for LVPECL Output, VCC = 2.375 V to 2.625 VGo
-
Changed recommended resistor values in Figure 12(a)Go
-
Changed recommended resistor values in Figure 16Go
-
Changed recommended resistor values in Figure 17Go
Changes from A Revision (October, 2009) to B Revision
-
Changed descriptions of INP0, INP1 and INN0, INN1 pins in tableGo
-
Changed descriptions of all output pins in tableGo