国产精品人人妻人色五月,国产美女在线精品免费观看,中文字幕日韩一区二区三区不卡

ZHCSLX4A October 2020 – December 2020 TPSM41615

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

MOV|69
- MPQF595

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

6.5 Electrical Characteristics

Limits apply over T_A = –40°C to +105°C, PV_IN= 12 V, V_IN = 12 V, V_OUT = 1.8 V, V_REF = 1.0 V, F_SW = 500 kHz, IOUT = 25 A, (unless otherwise noted); Minimum and maximum limits are specified through production test or by design. Typical values represent the most likely parametric norm and are provided for reference only.

PARAMETER		TEST CONDITIONS	MIN	TYP	MAX	UNIT
INPUT SUPPLY
PV_IN	Input switching voltage		4		16	V
V_IN	Input bias voltage		4		16	V
UVLO	PV_IN undervoltage lockout	PV_IN increasing, I_OUT = 0 A		3.2		V
	PV_IN undervoltage lockout	PV_IN decreasing, I_OUT = 2.5 A		3.0		V
	V_IN undervoltage lockout	V_IN increasing, I_OUT = 0 A		3.8		V
	V_IN undervoltage lockout	V_IN decreasing, I_OUT = 2.5 A		3.6		V
I_VIN	V_INbias current⁽¹⁾	V_RS+ = 1.2 V, I_OUT = 0 A, EN = OPEN, T_A= 25°C		4.3		mA
I_VIN-STBY	V_IN standby current	I_OUT = 0 A, EN = 0 V, T_A= 25°C		4.3		mA
OUTPUT VOLTAGE
V_OUT	Output voltage adjust	RS+ connected directly to V_OUT	0.6		1.1	V
	Output voltage adjust	RS+ connected to V_OUT feedback divider			7.1⁽¹⁾ ⁽²⁾	V
	V_OUTaccuracy	0.6V ≤ V_REF≤ 1.1V, V_RS+ = V_OUT,I_OUT = 0A, -40°C ≤ T_J = T_A ≤ 125°C⁽¹⁾	-1.0		1.0	%
	Line regulation	Over PV_IN range, PV_IN = V_IN, I_OUT = 0 A, T_A = 25°C		0.01		%
	Load regulation	Over I_OUT range, T_A = 25°C		0.03		%
OUTPUT CURRENT
I_OUT	Output current	Natural convection, T_A = 25°C	0		15⁽²⁾	A
I_OUT	Overcurrent threshold			22		A
I_SHARE	Current sharing for multi-phase operation⁽¹⁾	I_OUT ≤ 20 A/phase		±3		A
I_SHARE	Current sharing for multi-phase operation⁽¹⁾	I_OUT ≥ 20 A/phase		±15%
BP5 REGULATOR
V_BP5	BP5 regulator output voltage		4.5	5	5.5	V
V_BP5-DROPOUT	BP5 regulator dropout voltage⁽¹⁾	V_IN = 4.5 V, f_SW = 750 kHz, T_A = 25°C			365	mV
PERFORMANCE
η	Efficiency	I_OUT = 10 A		90		%
RS+
R_RS+-RS-	Lower feedback resistor from RS+ to RS-		0.995	1	1.005	kΩ
ENABLE
V_EN-H	EN rising threshold	I_OUT = 0 A	1.45	1.6	1.75	V
V_EN-L	EN falling threshold	I_OUT = 2.5 A		1.3		V
I_{EN_LKG}	EN input leakage current	V_IN= 4.5 V, I_OUT = 0 A	–1	0	1	μA
SOFT START
t_SS	Soft-start time⁽¹⁾	SS = OPEN		4		ms
t_SS-Range	Soft-start range⁽¹⁾	Programmable using SS pin	0.5		32	ms
PGOOD
V_PGOOD	PGOOD thresholds⁽¹⁾	V_RS+ rising (fault)		112%
		V_RS+ falling (good)		105%
		V_RS+ rising (good)		95%
		V_RS+ falling (fault)		88%
V_PGOOD-LOW	PGOOD low voltage with no supply voltage	PV_IN = V_IN = 0 V, I_PGOOD = 80 μA			0.8	V
I_PGOOD-LKG	PGOOD leakage current	V_IN= 4.5 V, V_PGOOD = 5 V, I_OUT = 0 A			15	μA
OVP / UVP
V_OVP	Overvoltage protection threshold⁽¹⁾	V_RS+ rising		117%
V_UVP	Under-voltage protection threshold⁽¹⁾	V_RS+ falling		83%
FREQUENCY and SYNC
f_SW	Switching frequency	VSEL = OPEN, RT = 44.2 k?, I_OUT = 2.5 A	450	500	550	kHz
f_SW	Switching frequency range⁽¹⁾	I_OUT = 2.5 A	300		1000	kHz
ton_min	Minimum on-time of SW⁽¹⁾			30		ns
toff_min	Minimum off-time of SW⁽¹⁾			340		ns
V_CLK-H	Logic-high for SYNC⁽¹⁾		2			V
V_CLK-L	Logic-low for SYNC⁽¹⁾				0.8	V
T_CLK-MIN	Minimum pulse width for SYNC⁽¹⁾	SYNC F_SW = 500 kHz	100			ns

(1) Ensured by design, not production tested.

(2) To determine IOUT range for a given set of conditions, see the Safe Operating Area graphs in "Typical Characteristics" section of the datasheet for more information.