人妻AV中文字幕无码专区,久久精品少妇毛片一个人看的WWW片高清在线 ,亚洲高清在线观看AV片

ZHCSKS5C September 2020 – January 2024 TPS3899

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

DSE|6
- MPDS287A

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

5.5 Electrical Characteristics

CTR = CTS = Open, RESET pull-up resistor (R_pull-up) = 100 kΩ to V_DD, output reset load (C_LOAD) = 10 pF and over the operating free-air temperature range –40℃ to 125℃, unless otherwise noted. V_DD ramp rate ≤ 1 V/μs. Typical values are at T_A = 25℃

PARAMETER		TEST CONDITIONS	MIN	TYP	MAX	UNIT
COMMON PARAMETERS
V_DD	Input supply voltage (Open Drain Low and Push Pull Low)		0.85		6	V
V_DD	Input supply voltage (Push Pull High)		1		6	V
V_IT– ⁽¹⁾	Negative-going input threshold range	for all output configs	0.8		5.4	V
V_ADJ-VIT–	Negative-going input threshold for adjustable sense threshold version			0.505		V
V_IT–accuracy	Negative-going input threshold accuracy	V_IT– = 0.505 V (ADJ version) or 0.8 V to 1.7 V (Fixed threshold)	–2.5	±0.5	2.5	%
V_IT–accuracy	Negative-going input threshold accuracy	V_IT– = 1.8 V to 5.4 V (Fixed threshold)	–2	±0.5	2	%
V_HYS	Hysteresis on V_IT–	V_IT– = 0.505 V and 0.8 V	3	5	8	%
V_HYS	Hysteresis on V_IT–	V_IT– = 0.9 V to 5.4 V	3	5	7	%
I_SENSE	Current into Sense pin, fixed threshold version	V_DD = V_SENSE = 6 V		0.025	0.1	μA
I_SENSE	Current into Sense pin, ADJ version	V_DD = V_SENSE = 6 V		0.025	0.05	μA
I_DD	Supply current into VDD pin when sense pin is separate	V_DD = V_SENSE = 6 V V_IT– = 0.505 V and 0.8 V to 5.4 V		0.125	1	μA
V_{TH_CTS}	Voltage threshold to stop CTS capacitor charge and assert RESET			0.73 * V_DD		V
V_{TH_CTR}	Voltage threshold to stop CTR capacitor charge and deassert RESET			0.73 * V_DD		V
R_CTS	CTS pin internal pull up resistance			500		kΩ
R_CTR	CTR pin internal pull up resistance			500		kΩ
TPS3899DL (Open-drain active-low)
V_POR	Power on reset voltage ⁽²⁾	V_OL(max) = 300 mV I_RESET(Sink) = 15 μA			700	mV
V_OL	Low level output voltage	V_DD = 0.85 V I_RESET(Sink) = 15 μA			300	mV
V_OL	Low level output voltage	V_DD = 3.3 V I_RESET(Sink) = 2 mA			300	mV
I_lkg(OD)	Open-Drain output leakage current	V_DD = V_PULLUP = 6 V, T_A = –40℃ to 85℃		10	100	nA
I_lkg(OD)	Open-Drain output leakage current	V_DD = V_PULLUP = 6 V		10	350	nA
TPS3899PL (Push-pull active-low)
V_POR	Power on reset voltage ⁽²⁾	V_OL(max) = 300 mV I_RESET(Sink) = 15 μA			700	mV
V_OL	Low level output voltage	V_DD = 0.85 V I_RESET(Sink) = 15 μA			300	mV
V_OL	Low level output voltage	V_DD = 3.3 V I_RESET(Sink) = 2 mA			300	mV
V_OH	High level output voltage	V_DD= 1.8 V I_{RESET(Source)} = 500 μA	0.8V_DD			V
		V_DD = 3.3 V I_{RESET(Source)} = 500 μA	0.8V_DD			V
		V_DD= 6 V I_{RESET(Source)} = 2 mA	0.8V_DD			V
TPS3899PH (Push-pull active-high)
V_POR	Power on reset voltage⁽²⁾	V_OH(min) = 0.8V_DD I_{RESET (Source)} = 15 uA			900	mV
V_OL	Low level output voltage	V_DD= 3.3 V I_RESET(Sink) = 500 μA			300	mV
V_OL	Low level output voltage	V_DD= 6 V I_RESET(Sink) = 2 mA			300	mV
V_OH	High level output voltage	V_DD = 1V I_RESET(Sink) = 15 μA	0.8V_DD			V
		V_DD= 1.5 V I_RESET(Sink) = 500 μA	0.8V_DD			V
		V_DD= 3.3 V I_RESET(Sink) = 2 mA	0.8V_DD			V

(1) V_IT- threshold voltage range from 0.8 V to 5.4 V (for DL, PL) and 1 to 5.4 V (for PH) in 100 mV steps, for released versions see Device Voltage Thresholds table.

(2) Minimum V_DD voltage level for a controlled output state. Below V_POR, the output cannot be determined.