ZHCSLZ4D May 2020 – September 2021 TPS25850-Q1 , TPS25851-Q1 , TPS25852-Q1
PRODUCTION DATA
- 1 特性
- 2 應用
- 3 說明
- 4 Revision History
- 5 說明（續）
- 6 Device Comparison Table
- 7 Pin Configuration and Functions
- 8 Specifications
- 9 Parameter Measurement Information
-
10Detailed Description
- 10.1 Overview
- 10.2 Functional Block Diagram
- 10.3
Feature Description
- 10.3.1 Power-Down or Undervoltage Lockout
- 10.3.2 Input Overvoltage Protection (OVP) - Continuously Monitored
- 10.3.3 Buck Converter
- 10.3.4 FREQ/SYNC
- 10.3.5 Bootstrap Voltage (BOOT)
- 10.3.6 Minimum ON-Time, Minimum OFF-Time
- 10.3.7 Internal Compensation
- 10.3.8 Selectable Output Voltage (VSET)
- 10.3.9 Current Limit and Short Circuit Protection
- 10.3.10 Cable Compensation
- 10.3.11 Thermal Management With Temperature Sensing (TS) and OTSD
- 10.3.12 Thermal Shutdown
- 10.3.13 USB Enable On/Off Control (TPS25852-Q1)
- 10.3.14 FAULT Indication (TPS25851-Q1 and TPS25852-Q1)
- 10.3.15 USB Specification Overview
- 10.3.16 USB Type-C? Basics
- 10.3.17 USB Port Operating Modes
- 10.4 Device Functional Modes
- 11Application and Implementation
- 12Power Supply Recommendations
- 13Layout
- 14Device and Documentation Support
- 15Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- RPQ|25
散熱焊盤機械數據 (封裝 | 引腳)
訂購信息
10.3.11 Thermal Management With Temperature Sensing (TS) and OTSD
The TS input pin allows for user-programmable thermal protection (for the TS pin thresholds, see the Electrical Characteristics). The TS input pin threshold is ratiometric with VSENSE. The external resistor divider setting, VTS, must be connected to the TPS2585x-Q1 SENSE pin to achieve accurate results (refer to the Figure 10-16). When VTS = 0.5 × VSENSE, the TPS2585x-Q1 performs below action:
- If operating with 3-A Type-C advertisement, the Px_CC1, Px_CC2 pin automatically reduces advertisement to the 1.5-A level.
Figure 10-16 TS InputIf the overtemperature condition persists, causing VTS = 0.65 × VSENSE, the TPS2585x-Q1 performs below actions:
- Broadcasts the default USB power mode, in default USB power, the charging is ideally reduced further per the USB2.0 and USB3.0 specification.
- Buck regulator output voltage at the SENS pin is reduced to 4.77 V.
If the overtemperature condition persists, causing TJ to reach the OTSD threshold, then the device thermal shuts down.Figure 10-17 shows the TPS25850-Q1 behavior when TS pin voltage trigger the Temp Warm and Temp Hot threshold.
Figure 10-17 TPS25850-Q1 Behavior When
Trigger Temp Warm/Hot ThresholdThe NTC thermistor must be placed near the hottest point on the PCB. In most cases, this placement is close to the SW node of the TPS2585x-Q1, near the buck inductor.
Tuning the VNTC threshold levels of VTEMP_WARM and VTEMP_HOT is achieved by adding RSER, RPARA, or both RSER and RPARA in conjunction with RNTC. Figure 10-18 is an example illustrating how to set the VTEMP_WARM threshold between 81°C and 90°C with a ΔT between TEMP_WARM assertion and TEMP_HOT assertion of 18°C to 29°C. Consult the chosen NTC manufacturer's specification for the value of β. Establishing the desired warning and shutdown thresholds can take some iteration.
Below is NTC spec and resistor value used in Figure 10-18 example.
- R0 = 470 kΩ. β = 4750. RNTC = R0 × exp β × (1/T – 1/T0).
- RPARA = 100 kΩ.
- RSER = 5.1 kΩ.
- RB = RNTC(at TEMP_WARM) = 27 kΩ.
Figure 10-18 VTS Threshold
Design Examples