ZHCSL92G May 2020 – March 2024 TLV9151-Q1 , TLV9152-Q1 , TLV9154-Q1
PRODUCTION DATA
| 參數 | 測試條件 | 最小值 | 典型值 | 最大值 | 單位 | ||
|---|---|---|---|---|---|---|---|
| 失調電壓 | |||||||
| VOS | 輸入失調電壓 | VCM = V– | ±125 | ±895 | μV | ||
| TA = -40°C 至 125°C | ±925 | ||||||
| dVOS/dT | 輸入失調電壓溫漂 | TA = -40°C 至 125°C | ±0.3 | μV/℃ | |||
| PSRR | 輸入失調電壓與電源間的關系 | VCM = V–，VS = 4V 至 16V | TA = -40°C 至 125°C | ±0.3 | ±1.5 | μV/V | |
| VCM = V–，VS = 2.7V 至 16V(4) | ±1 | ±10.6 | |||||
| 通道隔離 | f = 0Hz | 5 | μV/V | ||||
| 輸入偏置電流 | |||||||
| IB | 輸入偏置電流 | ±10 | pA | ||||
| TA = -40°C 至 125°C(4) | ±1 | nA | |||||
| IOS | 輸入失調電流 | ±10 | pA | ||||
| TA = -40°C 至 125°C(4) | ±1 | nA | |||||
| 噪聲 | |||||||
| EN | 輸入電壓噪聲 | f = 0.1Hz 至 10Hz | 1.8 | μVPP | |||
| 0.3 | μVRMS | ||||||
| eN | 輸入電壓噪聲密度 | f = 1kHz | 10.8 | nV/√Hz | |||
| f = 10kHz | 9.4 | ||||||
| iN | 輸入電流噪聲 | f = 1kHz | 2 | fA/√Hz | |||
| 輸入電壓范圍 | |||||||
| VCM | 共模電壓范圍 | (V–) – 0.1 | (V+) + 0.1 | V | |||
| CMRR | 共模抑制比 | VS = 16V，(V–) – 0.1V < VCM < (V+) – 2V（主輸入對） | TA = -40°C 至 125°C | 99 | 130 | dB | |
| VS = 4V，(V–) – 0.1V < VCM < (V+) – 2V（主輸入對） | 82 | 100 | |||||
| VS = 2.7V，(V–) – 0.1V < VCM < (V+) – 2V（主輸入對）(4) | 75 | 95 | |||||
| VS = 2.7V 至 16V，(V+) – 1V < VCM < (V+) + 0.1V（輔助輸入對） | 85 | ||||||
| 輸入電容 | |||||||
| ZID | 差分 | 100 || 9 | MΩ || pF | ||||
| ZICM | 共模 | 6 || 1 | TΩ || pF | ||||
| 開環增益 | |||||||
| AOL | 開環電壓增益 | VS = 16V，VCM = V– (V–) + 0.1V < VO < (V+) – 0.1V |
120 | 145 | dB | ||
| TA = -40°C 至 125°C | 142 | ||||||
| VS = 4V，VCM = V– (V–) + 0.1V < VO < (V+) – 0.1V |
104 | 130 | |||||
| TA = -40°C 至 125°C | 125 | ||||||
| VS = 2.7V，VCM = V– (V–) + 0.1V < VO < (V+) – 0.1V(4) |
101 | 120 | |||||
| TA = -40°C 至 125°C | 118 | ||||||
| 頻率響應 | |||||||
| GBW | 增益帶寬積 | 4.5 | MHz | ||||
| SR | 壓擺率 | VS = 16V，G = +1，CL = 20pF | 21 | V/μs | |||
| tS | 穩定時間 | 精度為 0.01%，VS = 16V，VSTEP = 10V，G = +1，CL = 20pF | 2.5 | μs | |||
| 精度為 0.01%，VS = 16V，VSTEP = 2V，G = +1，CL = 20pF | 1.5 | ||||||
| 精度為 0.1%，VS = 16V，VSTEP = 10V，G = +1，CL = 20pF | 2 | ||||||
| 精度為 0.1%，VS = 16V，VSTEP = 2V，G = +1，CL = 20pF | 1 | ||||||
| 相位裕度 | G = +1，RL = 10k? | 60 | ° | ||||
| 過載恢復時間 | VIN × 增益 > VS | 400 | ns | ||||
| THD+N | 總諧波失真 + 噪聲 (1) | VS = 16V，VO = 3 VRMS，G = 1，f = 1kHz | 0.00021% | ||||
| 輸出 | |||||||
| 相對于電源軌的電壓輸出擺幅（正和負） | VS = 16V，RL = 空載 | 5 | 10 | mV | |||
| TA = -40°C 至 125°C(4) | 15 | ||||||
| VS = 16V，RL = 10kΩ | 50 | 55 | |||||
| TA = -40°C 至 125°C(4) | 75 | ||||||
| VS = 16V，RL = 2kΩ | 200 | 250 | |||||
| TA = -40°C 至 125°C(4) | 350 | ||||||
| VS = 2.7V，RL = 空載 | 1 | 6 | |||||
| TA = -40°C 至 125°C(4) | 10 | ||||||
| VS = 2.7V，RL = 10kΩ | 5 | 12 | |||||
| TA = -40°C 至 125°C(4) | 18 | ||||||
| VS = 2.7V，RL = 2kΩ | 25 | 40 | |||||
| TA = -40°C 至 125°C(4) | 60 | ||||||
| ISC | 短路電流 | ±75 | mA | ||||
| CLOAD | 容性負載驅動 | 1000 |
pF | ||||
| ZO | 開環輸出阻抗 | f = 1MHz，IO = 0A | 525 | ? | |||
| 電源 | |||||||
| IQ | 每個放大器的靜態電流 | IO = 0 A | 560 | 685 | μA | ||
| IO = 0A，(TLV9151-Q1) | 560 | 691 | |||||
| IO = 0 A | TA = -40°C 至 125°C | 750 | |||||
| IO = 0A，(TLV9151-Q1) | 769 | ||||||
| 關斷 | |||||||
| IQSD | 每個放大器的靜態電流 | VS = 2.7V 至 16V，所有放大器均為禁用狀態，SHDN = V– | 30 | 45 | μA | ||
| ZSHDN | 關斷時的輸出阻抗 | VS = 2.7V 至 16V，放大器被禁用 | 320 || 2 | MΩ || pF | |||
| VIH | 邏輯高電平閾值電壓（放大器為啟用狀態） | (V–) + 0.8V | (V–) + 1.1V | V | |||
| VIL | 邏輯低電平閾值電壓（放大器為禁用狀態） | (V–) + 0.2V | (V–) + 0.8V | V | |||
| tON | 放大器啟用時間（完全關斷）(2) (3) | G = +1，VCM = V-，VO = 0.1 × VS/2 | 8 | μs | |||
| tON | 放大器啟用時間（部分關斷）(2) (3) | G = +1，VCM = V-，VO = 0.1 × VS/2 | 3 | ||||
| tOFF | 放大器禁用時間(2) | VCM = V-，VO = VS/2 | 3 | μs | |||
| SHDN 引腳輸入偏置電流（每個引腳） | VS = 2.7V 至 16V，(V+) ≥ SHDN ≥ (V–) + 0.9V | 500 | nA | ||||
| VS = 2.7V 至 16V，(V–) ≤ SHDN ≤ (V–) + 0.7V | 150 | ||||||