ZHCSI82E May 2018 – May 2019 THVD1410 , THVD1450 , THVD1451 , THVD1452
PRODUCTION DATA.
請參考 PDF 數據表獲取器件具體的封裝圖。
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |||
|---|---|---|---|---|---|---|---|---|
| Driver | ||||||||
| |VOD| | Driver differential output voltage magnitude | RL = 60 Ω, -15 V ≤ Vtest ≤ 15 V (See Figure 20)(2) | 1.5 | 3.5 | V | |||
| RL = 60 Ω, -15 V ≤ Vtest ≤ 15 V, 4.5 V ≤ VCC ≤ 5.5 V, (See Figure 20) | 2.1 | V | ||||||
| RL = 100 Ω (See Figure 21) | 2 | 4 | V | |||||
| RL = 54 Ω (See Figure 21) | 1.5 | 3.5 | V | |||||
| Δ|VOD| | Change in differential output voltage | RL = 54 Ω (See Figure 21) | -200 | 200 | mV | |||
| VOC | Common-mode output voltage | 1 | VCC/2 | 3 | V | |||
| ΔVOC(SS) | Change in steady-state common-mode output voltage | -200 | 200 | mV | ||||
| IOS | Short-circuit output current | DE = VCC, -7 V ≤ VO ≤ 12 V | -250 | 250 | mA | |||
| Receiver | ||||||||
| II | Bus input current | DE = 0 V, VCC = 0 V or 5.5 V | VI = 12V | 50 | 125 | µA | ||
| VI = -7V | -100 | -65 | µA | |||||
| DE = 0 V, VCC = 0 V or 5.5 V | VI = 15V | 60 | 125 | µA | ||||
| VI = -15V | -200 | -130 | µA | |||||
| VTH+ | Positive-going input threshold voltage | Over common-mode range of ± 15 V | See(1) | -100 | -20 | mV | ||
| VTH- | Negative-going input threshold voltage | -200 | -130 | See(1) | mV | |||
| VHYS | Input hysteresis | 30 | mV | |||||
| VOH | Output high voltage | IOH = -8 mA | VCC – 0.4 | VCC – 0.2 | V | |||
| VOL | Output low voltage | IOL = 8 mA | 0.2 | 0.4 | V | |||
| IOZR | Output high-impedance current | VO = 0 V or VCC, RE = VCC | -1 | 1 | µA | |||
| Logic | ||||||||
| IIN | Input current (D, DE, RE) | 3 V ≤ VCC ≤ 5.5 V, 0 V ≤ VIN ≤ VCC | -6.2 | 6.2 | µA | |||
| Device | ||||||||
| ICC | Supply current (quiescent) | Driver and receiver enabled | RE = 0 V , DE = VCC, No load | 2.4 | 3 | mA | ||
| Driver enabled, receiver disabled | RE = VCC, DE = VCC, No load | 2 | 2.5 | mA | ||||
| Driver disabled, receiver enabled | RE = 0 V, DE = 0 V, No load | 700 | 960 | µA | ||||
| Driver and receiver disabled | RE = VCC, DE = 0 V, D = open, No load | 0.1 | 1 | µA | ||||
| TSD | Thermal shutdown temperature | 170 | ℃ | |||||