色综合久久久久无码专区,欧美国产一级黄色,少妇人妻偷人精品无码视频新浪

ZHCSD11D September 2014 – December 2018 LP5907-Q1

UNLESS OTHERWISE NOTED, this document contains PRODUCTION DATA.

封裝選項

機械數據 (封裝 | 引腳)

DBV|5
- MPDS018T
DQN|4
- MPSS021E

散熱焊盤機械數據 (封裝 | 引腳)

DQN|4
- QFND355C

訂購信息

6.5 Electrical Characteristics

V_IN = V_OUT(NOM) + 1 V, V_EN = 1.2 V, I_OUT = 1 mA, C_IN = 1 µF, C_OUT = 1 µF (unless otherwise noted)⁽¹⁾⁽²⁾⁽³⁾

PARAMETER		TEST CONDITIONS		MIN	TYP	MAX	UNIT
GENERAL
V_IN	Input voltage	T_A= 25°C		2.2		5.5	V
ΔV_OUT	Output voltage tolerance	V_IN = (V_OUT(NOM) + 1 V) to 5.5 V, I_OUT = 1 mA to 250 mA, V_OUT ≥ 1.8 V		–2		2	%V_OUT
	Output voltage tolerance	V_IN = (V_OUT(NOM) + 1 V) to 5.5 V, I_OUT = 1 mA to 250 mA, V_OUT < 1.8 V		–3		3	%V_OUT
	Line regulation	V_IN = (V_OUT(NOM) + 1 V) to 5.5 V, I_OUT = 1 mA			0.02		%/V
	Load regulation	I_OUT= 1 mA to 250 mA			0.001		%/mA
I_LOAD	Output load current			0		250	mA
I_Q	Quiescent current⁽⁴⁾	V_EN = 1.2 V, I_OUT = 0 mA			12	25	µA
		V_EN = 1.2 V, I_OUT = 250 mA			250	425
		V_EN = 0.3 V (Disabled)			0.2	1
I_G	Ground current⁽⁵⁾	V_EN = 1.2 V, I_OUT = 0 mA			14		µA
V_DO	Dropout voltage⁽⁶⁾	I_OUT = 100 mA			50		mV
V_DO	Dropout voltage⁽⁶⁾	I_OUT = 250 mA				250	mV
I_SC	Short-circuit current limit	T_A= 25°C⁽⁷⁾		250	500		mA
PSRR	Power-supply rejection ratio⁽⁸⁾	f = 100 Hz, I_OUT = 20 mA			90		dB
		f = 1 kHz, I_OUT = 20 mA			82
		f = 10 kHz, I_OUT = 20 mA			65
		f = 100 kHz, I_OUT = 20 mA			60
e_N	Output noise voltage⁽⁸⁾	BW = 10 Hz to 100 kHz	I_OUT = 1 mA		10		µV_RMS
e_N	Output noise voltage⁽⁸⁾	BW = 10 Hz to 100 kHz	I_OUT = 250 mA		6.5		µV_RMS
R_AD	Output automatic discharge pulldown resistance	V_EN < V_IL (output disabled)			230		Ω
T_SD	Thermal shutdown	T_J rising			160		°C
T_SD	Thermal hysteresis	T_Jfalling from shutdown			15		°C
LOGIC INPUT THRESHOLDS
V_IL	Low input threshold	V_IN = 2.2 V to 5.5 V, V_EN falling until the output is disabled				0.4	V
V_IH	High input threshold	V_IN = 2.2 V to 5.5 V, V_ENrising until the output is enabled		1.2			V
I_EN	Input current at EN pin⁽⁹⁾	V_EN = 5.5 V and V_IN = 5.5 V			5.5		µA
I_EN	Input current at EN pin⁽⁹⁾	V_EN = 0 V and V_IN = 5.5 V			0.001		µA
TRANSIENT CHARACTERISTICS
ΔV_OUT	Line transient⁽⁸⁾	V_IN = (V_OUT(NOM) + 1 V) to (V_OUT(NOM) + 1.6 V) in 30 µs		–1			mV
	Line transient⁽⁸⁾	V_IN = (V_OUT(NOM) + 1.6 V) to (V_OUT(NOM) + 1.6 V) in 30 µs				1
	Load transient⁽⁸⁾	I_OUT = 1 mA to 250 mA in 10 µs		–40
	Load transient⁽⁸⁾	I_OUT = 250 mA to 1 mA in 10 µs				40
	Overshoot on start-up⁽⁸⁾	Stated as a percentage of V_OUT(NOM)				5%
	Overshoot on start-up with EN⁽⁸⁾	Stated as a percentage of V_OUT(NOM), V_IN = V_OUT + 1 V to 5.5 V, 0.7 µF < C_OUT < 10 µF, 0 mA < I_OUT < 250 mA, EN rising until the output is enabled				1%
t_ON	Turnon time	From V_EN > V_IH to V_OUT = 95% of V_OUT(NOM), T_A= 25°C			80	150	µs

(1) All voltages are with respect to the device GND terminal, unless otherwise stated.

(2) Minimum and maximum limits are ensured through test, design, or statistical correlation over the junction temperature (T_J) range of –40°C to 125°C, unless otherwise stated. Typical values represent the most likely parametric norm at T_A = 25°C, and are provided for reference purposes only.

(3) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (T_A-MAX) is dependent on the maximum operating junction temperature (T_J-MAX-OP = 125°C), the maximum power dissipation of the device in the application (P_D-MAX), and the junction-to ambient thermal resistance of the part/package in the application R_θJA), as given by the following equation: T_A-MAX = T_J-MAX-OP – (R_θJA × P_D-MAX). See Application and Implementation.

(4) Quiescent current is defined here as the difference in current between the input voltage source and the load at V_OUT.

(5) Ground current is defined here as the total current flowing to ground as a result of all input voltages applied to the device.

(6) Dropout voltage is the voltage difference between the input and the output at which the output voltage drops to 100 mV below its nominal value.

(7) Short-circuit current (I_SC) for the LP5907-Q1 is equivalent to current limit. To minimize thermal effects during testing, I_SC is measured with V_OUT pulled to 100 mV below its nominal voltage.

(8) This specification is verified by design.

(9) There is a 1-MΩ resistor between EN and ground on the device.