成人网站在线观看播放一区二区,欧美国产激情二区三区,久久69精品久久久久久HB

ZHCSGK0H August 2017 – January 2024 ISO7760 , ISO7761 , ISO7762 , ISO7763

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

DW|16
- MSOI003I
DBQ|16
- MSOI004H

散熱焊盤機械數據 (封裝 | 引腳)

DW|16
- QFND505A

訂購信息

5.6 Insulation Specifications

PARAMETER		TEST CONDITIONS		VALUE		UNIT
PARAMETER		TEST CONDITIONS		DW-16	DBQ-16	UNIT
CLR	External clearance⁽¹⁾	Shortest terminal-to-terminal distance through air		>8	>3.7	mm
CPG	External creepage⁽¹⁾	Shortest terminal-to-terminal distance across the package surface		>8	>3.7	mm
DTI	Distance through the insulation	Minimum internal gap (internal clearance)		>17	>17	μm
CTI	Comparative tracking index	DIN EN 60112 (VDE 0303-11); IEC 60112; UL 746A		>600	>600	V
	Material group	According to IEC 60664-1		I	I
	Overvoltage category per IEC 60664-1	Rated mains voltage ≤ 150 V_RMS		I-IV	I-IV
		Rated mains voltage ≤ 300 V_RMS		I-IV	I-III
		Rated mains voltage ≤ 600 V_RMS		I-IV	n/a
		Rated mains voltage ≤ 1000 V_RMS		I-III	n/a
DIN EN IEC 60747-17 (VDE 0884-17)⁽²⁾
V_IORM	Maximum repetitive peak isolation voltage	AC voltage (bipolar)		2121	566	V_PK
V_IOWM	Maximum working isolation voltage	AC voltage; Time dependent dielectric breakdown (TDDB) test; See Figure 8-7		1500	400	V_RMS
V_IOWM	Maximum working isolation voltage	DC voltage		2121	566	V_DC
V_IOTM	Maximum transient isolation voltage	V_TEST = V_IOTM, t = 60 s (qualification); V_TEST = 1.2 x V_IOTM, t= 1 s (100% production)	ISO7760	8000	4242	V_PK
V_IOTM	Maximum transient isolation voltage		ISO7761, ISO7762, ISO7763	7071	4242	V_PK
V_IMP	Maximum impulse voltage⁽³⁾	Tested in air, 1.2/50-μs waveform per IEC 62368-1		8000	4000	V_PK
V_IOSM	Maximum surge isolation voltage⁽⁴⁾	V_IOSM ≥ 1.3 x V_IMP; Tested in oil (qualification test), 1.2/50-μs waveform per IEC 62368-1		12800	10000	V_PK
q_pd	Apparent charge⁽⁵⁾	Method a, After Input-output safety test subgroup 2/3, V_ini = V_IOTM, t_ini = 60 s; V_pd(m) = 1.2 x V_IORM, t_m = 10 s		≤5	≤5	pC
		Method a, After environmental tests subgroup 1, V_ini = V_IOTM, t_ini = 60 s; V_pd(m) = 1.6 x V_IORM, t_m = 10 s		≤5	≤5
		Method b: At routine test (100% production) and preconditioning (type test); V_ini = 1.2 x V_IOTM, t_ini = 1 s; V_pd(m) = 1.875 x V_IORM, t_m = 1 s (method b1) or V_pd(m) = V_ini, t_m = t_ini (method b2)		≤5	≤5
C_IO	Barrier capacitance, input to output⁽⁶⁾	V_IO = 0.4 x sin (2πft), f = 1 MHz		~1.1	~0.9	pF
R_IO	Isolation resistance⁽⁶⁾	V_IO = 500 V, T_A = 25°C		>10¹²	>10¹²	Ω
		V_IO = 500 V, 100°C ≤ T_A ≤ 125°C		>10¹¹	>10¹¹
		V_IO = 500 V, T_S = 150°C		>10⁹	>10⁹
	Pollution degree			2	2
	Climatic category			55/125/21	55/125/21
UL 1577
V_ISO	Maximum withstanding isolation voltage	V_TEST = V_ISO , t = 60 s (qualification), V_TEST = 1.2 x V_ISO , t = 1 s (100% production)		5000	3000	V_RMS

(1) Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application. Care should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases. Techniques such as inserting grooves and/or ribs on a printed-circuit board are used to help increase these specifications.

(2) This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits.

(3) Testing is carried out in air to determine the surge immunity of the package

(4) Testing is carried out in oil to determine the intrinsic surge immunity of the isolation barrier.

(5) Apparent charge is electrical discharge caused by a partial discharge (pd).

(6) All pins on each side of the barrier tied together creating a two-terminal device.