国语对白叫床淫语刺激,四虎国产成人永久精品免费 ,国内精品免费久久久久电影院97

ZHCSM58B January 2020 – November 2021 BQ76952

PRODUCTION DATA

1 特性
2 應用
3 說明
4 Revision History
5 Device Comparison Table
6 Pin Configuration and Functions
7 Specifications
1. 7.1 Absolute Maximum Ratings
2. 7.2 ESD Ratings
3. 7.3 Recommended Operating Conditions
4. 7.4 Thermal Information BQ76952
5. 7.5 Supply Current
6. 7.6 Digital I/O
7. 7.7 LD Pin
8. 7.8 Precharge (PCHG) and Predischarge (PDSG) FET Drive
9. 7.9 FUSE Pin Functionality
10. 7.10 REG18 LDO
11. 7.11 REG0 Pre-regulator
12. 7.12 REG1 LDO
13. 7.13 REG2 LDO
14. 7.14 Voltage References
15. 7.15 Coulomb Counter
16. 7.16 Coulomb Counter Digital Filter (CC1)
17. 7.17 Current Measurement Digital Filter (CC2)
18. 7.18 Current Wake Detector
19. 7.19 Analog-to-Digital Converter
20. 7.20 Cell Balancing
21. 7.21 Cell Open Wire Detector
22. 7.22 Internal Temperature Sensor
23. 7.23 Thermistor Measurement
24. 7.24 Internal Oscillators
25. 7.25 High-side NFET Drivers
26. 7.26 Comparator-Based Protection Subsystem
27. 7.27 Timing Requirements - I2C Interface, 100kHz Mode
28. 7.28 Timing Requirements - I2C Interface, 400kHz Mode
29. 7.29 Timing Requirements - HDQ Interface
30. 7.30 Timing Requirements - SPI Interface
31. 7.31 Interface Timing Diagrams
32. 7.32 Typical Characteristics
8 Device Description
1. 8.1 Overview
2. 8.2 Functional Block Diagram
3. 8.3 BQ76952 Device Versions
4. 8.4 Diagnostics
9 Device Configuration
1. 9.1 Commands and Subcommands
2. 9.2 Configuration Using OTP or Registers
3. 9.3 Device Security
4. 9.4 Scratchpad Memory
10Measurement Subsystem
1. 10.1 Voltage Measurement
2. 10.2 General Purpose ADCIN Functionality
3. 10.3 Coulomb Counter and Digital Filters
4. 10.4 Synchronized Voltage and Current Measurement
5. 10.5 Internal Temperature Measurement
6. 10.6 Thermistor Temperature Measurement
7. 10.7 Factory Trim of Voltage ADC
8. 10.8 Voltage Calibration (ADC Measurements)
9. 10.9 Voltage Calibration (COV and CUV Protections)
10. 10.10 Current Calibration
11. 10.11 Temperature Calibration
11Primary and Secondary Protection Subsystems
1. 11.1 Protections Overview
2. 11.2 Primary Protections
3. 11.3 Secondary Protections
4. 11.4 High-Side NFET Drivers
5. 11.5 Protection FETs Configuration and Control
  1. 11.5.1 FET Configuration
  2. 11.5.2 PRECHARGE and PREDISCHARGE Modes
6. 11.6 Load Detect Functionality
12Device Hardware Features
1. 12.1 Voltage References
2. 12.2 ADC Multiplexer
3. 12.3 LDOs
  1. 12.3.1 Preregulator Control
  2. 12.3.2 REG1 and REG2 LDO Controls
4. 12.4 Standalone Versus Host Interface
5. 12.5 Multifunction Pin Controls
6. 12.6 RST_SHUT Pin Operation
7. 12.7 CFETOFF, DFETOFF, and BOTHOFF Pin Functionality
8. 12.8 ALERT Pin Operation
9. 12.9 DDSG and DCHG Pin Operation
10. 12.10 Fuse Drive
11. 12.11 Cell Open Wire
12. 12.12 Low Frequency Oscillator
13. 12.13 High Frequency Oscillator
13Device Functional Modes
1. 13.1 Overview
2. 13.2 NORMAL Mode
3. 13.3 SLEEP Mode
4. 13.4 DEEPSLEEP Mode
5. 13.5 SHUTDOWN Mode
6. 13.6 CONFIG_UPDATE Mode
14Serial Communications Interface
1. 14.1 Serial Communications Overview
2. 14.2 I2C Communications
3. 14.3 SPI Communications
  1. 14.3.1 SPI Protocol
4. 14.4 HDQ Communications
15Cell Balancing
1. 15.1 Cell Balancing Overview
16Application and Implementation
1. 16.1 Application Information
2. 16.2 Typical Applications
3. 16.3 Random Cell Connection Support
4. 16.4 Startup Timing
5. 16.5 FET Driver Turn-Off
6. 16.6 Unused Pins
17Power Supply Requirements
18Layout
1. 18.1 Layout Guidelines
2. 18.2 Layout Example
19Device and Documentation Support
1. 19.1 Documentation Support
2. 19.2 支持資源
3. 19.3 Trademarks
4. 19.4 Electrostatic Discharge Caution
5. 19.5 術語表
20Mechanical, Packaging, Orderable Information

封裝選項

機械數據 (封裝 | 引腳)

PFB|48
- MTQF019B

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

7.11 REG0 Pre-regulator

Typical values stated where T_A = 25°C and V_BAT = 59.2 V, min/max values stated where T_A = -40°C to 85°C and V_BAT = 4.7 V to 80 V (unless otherwise noted)⁽¹⁾

PARAMETER		TEST CONDITIONS	MIN	TYP	MAX	UNIT
V_{BREG_HDRM}	Pre-regulator control voltage headroom ( min(V_BAT - V_BREG) )⁽⁴⁾	V_BAT ≥ 4.7 V		1.5	1.91	V
V_{REGIN_INT}	Pre-regulator voltage, when generated using BREG	V_BAT > 8 V, although specific requirement depends on external device selected	5	5.5	5.8	V
V_{REGIN_EXT}	Pre-regulator voltage when using externally supplied REGIN⁽⁴⁾	See requirements based on settings of REG1 and REG2			5.5	V
ΔV_O(TEMP)	Regulator output over temperature	ΔV_REGIN vs V_REGIN at 25°C, I_REGIN = 50 mA, V_BAT > 8 V		±0.05		%
I_Max	Maximum current driven out from BREG⁽⁴⁾	Under short circuit conditions (V_REGIN = 0 V)	2.5	3.33		mA
C_EXT	External capacitor REGIN to VSS⁽³⁾ ⁽⁴⁾		15	22	27	nF
C_BREG	External capacitor BREG to VSS⁽⁴⁾				150	pF

(1) Operation with V_BAT up to 80 V is supported when the charge pump is not in operation. Whenever the charge pump is in operation (in 5.5 V or 11 V mode), the maximum voltage on V_BAT should be reduced to ensure the voltage on CP1, CHG, and DSG does not exceed their maximum specified voltage.

(3) Capacitance should be above 7 nF after consideration for aging and derating.

(4) Specified by design