亚洲综合色在线一区二区 ,四虎国产成人永久精品免费 ,亚洲欧洲国产成人综合在线

ZHCSM58B January 2020 – November 2021 BQ76952

PRODUCTION DATA

1 特性
2 應用
3 說明
4 Revision History
5 Device Comparison Table
6 Pin Configuration and Functions
7 Specifications
1. 7.1 Absolute Maximum Ratings
2. 7.2 ESD Ratings
3. 7.3 Recommended Operating Conditions
4. 7.4 Thermal Information BQ76952
5. 7.5 Supply Current
6. 7.6 Digital I/O
7. 7.7 LD Pin
8. 7.8 Precharge (PCHG) and Predischarge (PDSG) FET Drive
9. 7.9 FUSE Pin Functionality
10. 7.10 REG18 LDO
11. 7.11 REG0 Pre-regulator
12. 7.12 REG1 LDO
13. 7.13 REG2 LDO
14. 7.14 Voltage References
15. 7.15 Coulomb Counter
16. 7.16 Coulomb Counter Digital Filter (CC1)
17. 7.17 Current Measurement Digital Filter (CC2)
18. 7.18 Current Wake Detector
19. 7.19 Analog-to-Digital Converter
20. 7.20 Cell Balancing
21. 7.21 Cell Open Wire Detector
22. 7.22 Internal Temperature Sensor
23. 7.23 Thermistor Measurement
24. 7.24 Internal Oscillators
25. 7.25 High-side NFET Drivers
26. 7.26 Comparator-Based Protection Subsystem
27. 7.27 Timing Requirements - I2C Interface, 100kHz Mode
28. 7.28 Timing Requirements - I2C Interface, 400kHz Mode
29. 7.29 Timing Requirements - HDQ Interface
30. 7.30 Timing Requirements - SPI Interface
31. 7.31 Interface Timing Diagrams
32. 7.32 Typical Characteristics
8 Device Description
1. 8.1 Overview
2. 8.2 Functional Block Diagram
3. 8.3 BQ76952 Device Versions
4. 8.4 Diagnostics
9 Device Configuration
1. 9.1 Commands and Subcommands
2. 9.2 Configuration Using OTP or Registers
3. 9.3 Device Security
4. 9.4 Scratchpad Memory
10Measurement Subsystem
1. 10.1 Voltage Measurement
2. 10.2 General Purpose ADCIN Functionality
3. 10.3 Coulomb Counter and Digital Filters
4. 10.4 Synchronized Voltage and Current Measurement
5. 10.5 Internal Temperature Measurement
6. 10.6 Thermistor Temperature Measurement
7. 10.7 Factory Trim of Voltage ADC
8. 10.8 Voltage Calibration (ADC Measurements)
9. 10.9 Voltage Calibration (COV and CUV Protections)
10. 10.10 Current Calibration
11. 10.11 Temperature Calibration
11Primary and Secondary Protection Subsystems
1. 11.1 Protections Overview
2. 11.2 Primary Protections
3. 11.3 Secondary Protections
4. 11.4 High-Side NFET Drivers
5. 11.5 Protection FETs Configuration and Control
  1. 11.5.1 FET Configuration
  2. 11.5.2 PRECHARGE and PREDISCHARGE Modes
6. 11.6 Load Detect Functionality
12Device Hardware Features
1. 12.1 Voltage References
2. 12.2 ADC Multiplexer
3. 12.3 LDOs
  1. 12.3.1 Preregulator Control
  2. 12.3.2 REG1 and REG2 LDO Controls
4. 12.4 Standalone Versus Host Interface
5. 12.5 Multifunction Pin Controls
6. 12.6 RST_SHUT Pin Operation
7. 12.7 CFETOFF, DFETOFF, and BOTHOFF Pin Functionality
8. 12.8 ALERT Pin Operation
9. 12.9 DDSG and DCHG Pin Operation
10. 12.10 Fuse Drive
11. 12.11 Cell Open Wire
12. 12.12 Low Frequency Oscillator
13. 12.13 High Frequency Oscillator
13Device Functional Modes
1. 13.1 Overview
2. 13.2 NORMAL Mode
3. 13.3 SLEEP Mode
4. 13.4 DEEPSLEEP Mode
5. 13.5 SHUTDOWN Mode
6. 13.6 CONFIG_UPDATE Mode
14Serial Communications Interface
1. 14.1 Serial Communications Overview
2. 14.2 I2C Communications
3. 14.3 SPI Communications
  1. 14.3.1 SPI Protocol
4. 14.4 HDQ Communications
15Cell Balancing
1. 15.1 Cell Balancing Overview
16Application and Implementation
1. 16.1 Application Information
2. 16.2 Typical Applications
3. 16.3 Random Cell Connection Support
4. 16.4 Startup Timing
5. 16.5 FET Driver Turn-Off
6. 16.6 Unused Pins
17Power Supply Requirements
18Layout
1. 18.1 Layout Guidelines
2. 18.2 Layout Example
19Device and Documentation Support
1. 19.1 Documentation Support
2. 19.2 支持資源
3. 19.3 Trademarks
4. 19.4 Electrostatic Discharge Caution
5. 19.5 術語表
20Mechanical, Packaging, Orderable Information

封裝選項

機械數據 (封裝 | 引腳)

PFB|48
- MTQF019B

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

10.1.3 Cell 1 Voltage Validation During SLEEP Mode

In rare cases, an invalid Cell 1 Voltage() reading has been observed to occur in some devices taken during SLEEP mode.

While the device is in SLEEP mode, each result obtained from reading the Cell 1 Voltage() must be validated before it can be considered valid. During SLEEP mode, current is below programmable thresholds, so the pack is typically not being charged or discharged with any significant level of current. Thus, the cell voltages will generally not be changing significantly.

In order to determine if a measurement of Cell 1 Voltage() taken during SLEEP mode is valid, it is necessary to compare each measurement to measurements taken before and after the particular measurement. It is important that these three readings represent three separate measurements for the Cell 1 Voltage(). If the reading is significantly different from the separate readings taken before and after, then that reading is considered invalid and should be discarded.

In order to ensure the three measurements read from the device are truly separate measurements, the host can read the measurements at intervals exceeding Power:Sleep:Voltage Time while the device is in SLEEP mode. This is necessary to avoid the host reading an existing measurement multiple times, before a new measurement has been taken and is available for readout.

An invalid Cell 1 Voltage() reading may result in an SUV PF Alert being set but does not result in an SUV PF status fault if the SUV Delay is set to 1 second or longer. It also does not trigger a Cell Undervoltage (CUV) Protection alert or status fault, since this protection uses a comparator for its detection. If a reading reported by Cell 1 Voltage() is below the Protections:CUV:Threshold level and the CUV protection is enabled, but the CUV Alert is not triggered, this also can be used as an indication the reading is invalid.

This validation process is necessary to ensure that valid Cell 1 Voltage() results are measured.