主頁 電源管理 LED 驅動器 RGB LED 驅動器

TLC59116F

正在供貨

16 位快速模式增強版 (FM+) I2C 總線 LED 驅動器

產品詳情

Number of channels 16 LED current per channel (mA) 120 LED configuration Parallel, Series, Single Program memory No Topology Current Sink, Linear Programmable ramp control No Vin (min) (V) 3 Vin (max) (V) 5.5 Iout (max) (A) 1.92 Features I2C control Iq (typ) (mA) 13 Operating temperature range (°C) -40 to 85 Rating Catalog
Number of channels 16 LED current per channel (mA) 120 LED configuration Parallel, Series, Single Program memory No Topology Current Sink, Linear Programmable ramp control No Vin (min) (V) 3 Vin (max) (V) 5.5 Iout (max) (A) 1.92 Features I2C control Iq (typ) (mA) 13 Operating temperature range (°C) -40 to 85 Rating Catalog
TSSOP (PW) 28 62.08 mm2 9.7 x 6.4 VQFN (RHB) 32 25 mm2 5 x 5
  • 16 LED Drivers (Each Output Programmable at
    OFF, ON, LED Brightness, and Group
    Dimming/Blinking Mixed With Individual LED
    Brightness)
  • 16 Open-Drain Output Channels
  • 256-Step (8-Bit) Linear Programmable Brightness
    Per LED Output Varying From Fully OFF (Default)
    to Maximum Brightness Using a 97-kHz PWM Signal
  • 256-Step Group Brightness Control Allows
    General Dimming (Using a 190-Hz PWM Signal
    From Fully OFF to Maximum Brightness (Default)
  • 256-Step Group Blinking With Frequency
    Programmable From 24 Hz to 10.73 s and Duty
    Cycle from 0% to 99.6%
  • Four Hardware Address Pins Allow 14
    TLC59116F Devices to be Connected to the
    Same I2C Bus
  • Four Software-Programmable I2C Bus Addresses
    (One LED Group Call Address and Three LED
    Sub-Call Addresses) Allow Groups of Devices to
    be AddressedSimultaneously in Any Combination
    (For example, One Register Used for ‘All Call’ So
    All the TLC59116Fs on the I2C Bus Can be
    Addressed at the Same Time and the Second
    Register Used for Three Different Addresses So
    That 1/3 of all Devices on the Bus Can Be
    Addressed at the Same Time in a Group).
    Software Enable and Disable for I2C Bus Address.
  • Software Reset Feature (SWRST Call) Allows the
    Device to be Reset Through the I2C Bus
  • Up to 14 Possible Hardware Adjustable Individual
    I2C Bus Addresses Per Device so That Each
    Device Can be Programmed
  • Output State Change Programmable on the
    Acknowledge or the STOP Command to Update
    Outputs Byte-by-Byte or All at the Same Time
    (Default to Change on STOP.
  • 120-mA Maximum Output Current
  • 17-V Maximum Output Voltage
  • 25-MHz Internal Oscillator Requires No External Components
  • 1-MHz Fast-Mode Plus (FM+) Compatible I2C Bus
    Interface With 30 mA High Drive Capability on
    SDA Output for Driving High Capacity Buses
  • Internal Power-On Reset
  • Noise Filter on SCL/SDA Inputs
  • No Glitch on Power Up
  • Active-Low Reset
  • Supports Hot Insertion
  • Low Standby Current
  • 3.3-V or 5-V Supply Voltage
  • 5.5-V Tolerant Inputs
  • 28-Pin TSSOP (PW)
  • –40°C to 85°C Operation
  • APPLICATIONS
    • Gaming
    • Small Signage
    • Industrial Equipment

All other trademarks are the property of their respective owners
  • 16 LED Drivers (Each Output Programmable at
    OFF, ON, LED Brightness, and Group
    Dimming/Blinking Mixed With Individual LED
    Brightness)
  • 16 Open-Drain Output Channels
  • 256-Step (8-Bit) Linear Programmable Brightness
    Per LED Output Varying From Fully OFF (Default)
    to Maximum Brightness Using a 97-kHz PWM Signal
  • 256-Step Group Brightness Control Allows
    General Dimming (Using a 190-Hz PWM Signal
    From Fully OFF to Maximum Brightness (Default)
  • 256-Step Group Blinking With Frequency
    Programmable From 24 Hz to 10.73 s and Duty
    Cycle from 0% to 99.6%
  • Four Hardware Address Pins Allow 14
    TLC59116F Devices to be Connected to the
    Same I2C Bus
  • Four Software-Programmable I2C Bus Addresses
    (One LED Group Call Address and Three LED
    Sub-Call Addresses) Allow Groups of Devices to
    be AddressedSimultaneously in Any Combination
    (For example, One Register Used for ‘All Call’ So
    All the TLC59116Fs on the I2C Bus Can be
    Addressed at the Same Time and the Second
    Register Used for Three Different Addresses So
    That 1/3 of all Devices on the Bus Can Be
    Addressed at the Same Time in a Group).
    Software Enable and Disable for I2C Bus Address.
  • Software Reset Feature (SWRST Call) Allows the
    Device to be Reset Through the I2C Bus
  • Up to 14 Possible Hardware Adjustable Individual
    I2C Bus Addresses Per Device so That Each
    Device Can be Programmed
  • Output State Change Programmable on the
    Acknowledge or the STOP Command to Update
    Outputs Byte-by-Byte or All at the Same Time
    (Default to Change on STOP.
  • 120-mA Maximum Output Current
  • 17-V Maximum Output Voltage
  • 25-MHz Internal Oscillator Requires No External Components
  • 1-MHz Fast-Mode Plus (FM+) Compatible I2C Bus
    Interface With 30 mA High Drive Capability on
    SDA Output for Driving High Capacity Buses
  • Internal Power-On Reset
  • Noise Filter on SCL/SDA Inputs
  • No Glitch on Power Up
  • Active-Low Reset
  • Supports Hot Insertion
  • Low Standby Current
  • 3.3-V or 5-V Supply Voltage
  • 5.5-V Tolerant Inputs
  • 28-Pin TSSOP (PW)
  • –40°C to 85°C Operation
  • APPLICATIONS
    • Gaming
    • Small Signage
    • Industrial Equipment

All other trademarks are the property of their respective owners

The TLC59116F is an I2C-bus controlled 16-channel LED driver optimized for red/green/blue/amber (RGBA) color mixing applications. Each LED output has its own 8-bit resolution (256 steps) fixed frequency individual PWM controller that operates at 97 kHz with a duty cycle that is adjustable from 0% to 99.6% to allow the LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps) group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency between 24 Hz to once every 10.73 seconds with a duty cycle that is adjustable from 0% to 99.6% that is used to either dim or blink all LEDs with the same value.

The TLC59116F is an I2C-bus controlled 16-channel LED driver optimized for red/green/blue/amber (RGBA) color mixing applications. Each LED output has its own 8-bit resolution (256 steps) fixed frequency individual PWM controller that operates at 97 kHz with a duty cycle that is adjustable from 0% to 99.6% to allow the LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps) group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency between 24 Hz to once every 10.73 seconds with a duty cycle that is adjustable from 0% to 99.6% that is used to either dim or blink all LEDs with the same value.
下載 觀看帶字幕的視頻 視頻

技術文檔

star =有關此產品的 TI 精選熱門文檔
未找到結果。請清除搜索并重試。
查看全部 6
類型 標題 下載最新的英語版本 日期
* 數據表 TLC59116F 16-Channel Fast-Mode Plus I2C Bus LED Driver 數據表 (Rev. C) 2015年 9月 25日
白皮書 常見 LED 功能和 LED 驅動器設計注意事項 英語版 2020年 9月 21日
應用手冊 How to Select a RGB LED Driver 2019年 8月 8日
選擇指南 電源管理指南 2018 (Rev. K) 2018年 7月 31日
選擇指南 電源管理指南 2018 (Rev. R) 2018年 6月 25日
用戶指南 TLC59116FEVM-571 2010年 2月 11日

設計和開發

如需其他信息或資源，請點擊以下任一標題進入詳情頁面查看（如有）。

評估板

TLC59116FEVM-571 — 16 通道 LED 驅動器評估模塊

TLC59116F 是 I2C 總線控制的 16 通道 LED 驅動器，它針對娛樂產品的紅色/綠色/藍色/琥珀色 (RGBA) 混合和背光應用進行了優化。每個 LED 輸出都擁有自身的 8 位分辨率（256 色階）、固定頻率、獨立 PWM 控制器（工作頻率為 97kHz）和可調節占空比（0% 至 99.6%）。獨立 PWM 控制器允許將每個 LED 設置為特定的亮度值。附加的 8 位分辨率（256 色階）組合式 PWM 控制器既具有 190Hz 的固定頻率，又擁有低至 24Hz 的可調節頻率（每隔 10.73 秒調節一次）和可調節占空比（0% 至 99.6%）。組合式 PWM (...)
用戶指南: PDF
TI.com 上無現貨
支持軟件

TLC59116EVM-SW — 用于 TLC59116 評估模塊的軟件

TLC59116EVM-SW 軟件為 TLC59116 EVM 板提供軟件接口。使用本軟件通過 USB 接口適配器來更改 TLC59116 IC 內部寄存器，同時控制與 EVM 相連的 LED 顯示屏。

下載：安裝用于 TLC59116EVM-SW 的軟件

下載選項
模擬工具

PSPICE-FOR-TI — PSpice? for TI 設計和仿真工具

PSpice? for TI 可提供幫助評估模擬電路功能的設計和仿真環境。此功能齊全的設計和仿真套件使用 Cadence? 的模擬分析引擎。PSpice for TI 可免費使用，包括業內超大的模型庫之一，涵蓋我們的模擬和電源產品系列以及精選的模擬行為模型。

借助?PSpice for TI 的設計和仿真環境及其內置的模型庫，您可對復雜的混合信號設計進行仿真。創建完整的終端設備設計和原型解決方案，然后再進行布局和制造，可縮短產品上市時間并降低開發成本。?

在?PSpice for TI 設計和仿真工具中，您可以搜索 TI (...)
發送申請
封裝 引腳 CAD 符號、封裝和 3D 模型
TSSOP (PW) 28 Ultra Librarian
VQFN (RHB) 32 Ultra Librarian

訂購和質量

包含信息：
  • RoHS
  • REACH
  • 器件標識
  • 引腳鍍層/焊球材料
  • MSL 等級/回流焊峰值溫度
  • MTBF/時基故障估算
  • 材料成分
  • 鑒定摘要
  • 持續可靠性監測
包含信息：
  • 制造廠地點
  • 封裝廠地點

推薦產品可能包含與 TI 此產品相關的參數、評估模塊或參考設計。

支持和培訓

可獲得 TI 工程師技術支持的 TI E2E? 論壇

所有內容均由 TI 和社區貢獻者按“原樣”提供，并不構成 TI 規范。請參閱使用條款。

如果您對質量、包裝或訂購 TI 產品有疑問，請參閱 TI 支持。??????????????

視頻