CD4047B
- Lower power consumption: special CMOS oscillator configuration
- Monostable (one-shot) or astable (free-running) operation
- True and complemented buffered outputs
- Only one external R anc C required
- Buffered inputs
- 100% tested for quiescent current at 20 V
- Standardized, symmetrical output characteristics
- 5-V, 10-V, and 15-V parametric ratings
- Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of 'B' Series CMOS Devices"
- Monostable Multivibrator Features:
- Positive-or negative-edge trigger
- Output pulse width independent of trigger pulse duration
- Retriggerable option for pulse width expansion
- Internal power-on reset circuit
- Long pulse widths possible using small RC components by means of external counter provision
- Fast recovery time essentially independent of pulse width
- Pulse-width accuracy maintained at duty cycles approaching 100%
- Astable Multivibrator Features:
- Free-running or gatable operating modes
- 50% duty cycle
- Oscillator output available
- Good astable frequency stability:
Frequency deviation:
= ±2% + 0.03%/°C @ 100 kHz
= ±0.5% +0.015%/°C @ 10 kHz (circuits "trimmed" to frequency VDD = 10 V ± 10%)
- Applications:
Digital equipment where low-power dissipation and/or high noise immunity are primary design requirements:- Envelope detection
- Frequency multiplication
- Frequency division
- Frequency discriminators
- Timing circuits
- Time-delay applications
Data sheet acquired from Harris Semiconductor
CD4047B consists of a gatable astable multivibrator with logic techniques incorporated to permit positive or negative edge-triggered monostable multivibrator action with retriggering and external counting options.
Inputs include +TRIGGER, -TRIGGER, ASTABLE, ASTABLE\, RETRIGGER, and EXTERNAL RESET. Buffered outputs are Q\, Q and OSCILLATOR. In all modes of operation, and external capacitor must be connected between C-Timing and RC-Common terminal, and an external resistor must be connected between the R-Timing and RC-Common terminals.
Astable operation is enabled by a high level on the STABLE input or a low level on the ASTABLE\ input, or both. The period of the square wave at the Q and Q\ Outputs in this mode off operation is a function of the external components employed. "True" input pulses on the ASTABLE input or "Complement" pulses on the ASTABLE\ input allow the circuit to be used as a gatable multivibrator. The OSCILLATOR output period will be half of the Q terminal output in the astable mode. However, a 50% duty cycle is not guaranteed at this output.
The CD4047B triggers in the monostable mode when a positive-going edge occurs on the +TRIGGER-input while the -TRIGGER is held low. INput pulses may be of any duration relative to the output pulse.
If retrigger capability is desired, the RETRIGGER input is pulsed. The retriggerable mode of operation is limited to positive-going edge. The CD4047B will retrigger as long as the RETRIGGER-input is high, with or without transitions (See Fig. 34).
An external countdown option can be implemented by coupling "Q" to an external "N" counter and resetting the counter with the trigger pulse. The counter output pulse is fed back to the ASTABLE\ input and has a duration equal to N times the period of the multivibrator.
A high level on the EXTERNAL RESET input assures no output pulse during an "ON" power condition. This input can also be activated to terminate the output pulse at any tine. For monostable operation, whenever VDD is applied, and internal power-on reset circuit will clock the Q output low within one output period (tM).
The CD4047B-Series types are supplied in 14-lead hermetic dual-in-line ceramic packages (F3A suffix), 14-lead dual-in-line plastic packages (E suffix), 14-lead small outline packages (M, MT, M96, and NSR suffixes), and 14-lead thin shrink small-outline packages (PW and PWR suffixes).
您可能感興趣的相似產品
功能與比較器件相同，且具有相同引腳
技術文檔
| 類型 | 標題 | 下載最新的英語版本 | 日期 | |||
|---|---|---|---|---|---|---|
| * | 數據表 | CD4047B TYPES 數據表 (Rev. C) | 2003年 8月 21日 | |||
| 應用手冊 | 使用 SN74LVC1G123 單穩多諧振蕩器進行設計 (Rev. A) | PDF | HTML | 英語版 (Rev.A) | PDF | HTML | 2021年 7月 20日 | |
| 選擇指南 | Logic Guide (Rev. AB) | 2017年 6月 12日 | ||||
| 應用手冊 | Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) | 2015年 12月 2日 | ||||
| 選擇指南 | 邏輯器件指南 2014 (Rev. AA) | 最新英語版本 (Rev.AC) | PDF | HTML | 2014年 11月 17日 | ||
| 用戶指南 | LOGIC Pocket Data Book (Rev. B) | 2007年 1月 16日 | ||||
| 應用手冊 | Semiconductor Packing Material Electrostatic Discharge (ESD) Protection | 2004年 7月 8日 | ||||
| 用戶指南 | Signal Switch Data Book (Rev. A) | 2003年 11月 14日 | ||||
| 應用手冊 | Understanding Buffered and Unbuffered CD4xxxB Series Device Characteristics | 2001年 12月 3日 | ||||
| 選擇指南 | Logic Guide (Rev. AC) | PDF | HTML | 1994年 6月 1日 |
設計和開發
如需其他信息或資源，請點擊以下任一標題進入詳情頁面查看（如有）。
14-24-LOGIC-EVM — 采用 14 引腳至 24 引腳 D、DB、DGV、DW、DYY、NS 和 PW 封裝的邏輯產品通用評估模塊
14-24-LOGIC-EVM 評估模塊 (EVM) 設計用于支持采用 14 引腳至 24 引腳 D、DW、DB、NS、PW、DYY 或 DGV 封裝的任何邏輯器件。
| 封裝 | 引腳 | CAD 符號、封裝和 3D 模型 |
|---|---|---|
| PDIP (N) | 14 | Ultra Librarian |
| SOIC (D) | 14 | Ultra Librarian |
| SOP (NS) | 14 | Ultra Librarian |
| TSSOP (PW) | 14 | Ultra Librarian |
訂購和質量
- RoHS
- REACH
- 器件標識
- 引腳鍍層/焊球材料
- MSL 等級/回流焊峰值溫度
- MTBF/時基故障估算
- 材料成分
- 鑒定摘要
- 持續可靠性監測
- 制造廠地點
- 封裝廠地點