ZHCS761F December   2011  – May 2017 TRF7962A

PRODUCTION DATA.  

1. 1器件概述
   1. 1.1 特性
   2. 1.2 應用
   3. 1.3 說明
   4. 1.4 應用框圖
2. 2修訂歷史記錄
3. 3Device Characteristics
   1. 3.1 Related Products
4. 4Terminal Configuration and Functions
   1. 4.1 Pin Diagrams
   2. 4.2 Signal Descriptions
5. 5Specifications
   1. 5.1 Absolute Maximum Ratings
   2. 5.2 ESD Ratings
   3. 5.3 Recommended Operating Conditions
   4. 5.4 Electrical Characteristics
   5. 5.5 Thermal Resistance Characteristics
   6. 5.6 Switching Characteristics
6. 6Detailed Description
   1. 6.1  Functional Block Diagram
   2. 6.2  Power Supplies
   3. 6.3  Supply Arrangements
   4. 6.4  Supply Regulator Settings
   5. 6.5  Power Modes
   6. 6.6  Receiver – Analog Section
      1. 6.6.1 Main and Auxiliary Receiver
      2. 6.6.2 Receiver Gain and Filter Stages
   7. 6.7  Receiver – Digital Section
      1. 6.7.1 Received Signal Strength Indicator (RSSI)
         1. 6.7.1.1 Internal RSSI – Main and Auxiliary Receivers
         2. 6.7.1.2 External RSSI
   8. 6.8  Oscillator Section
   9. 6.9  Transmitter - Analog Section
   10. 6.10 Transmitter - Digital Section
   11. 6.11 Transmitter – External Power Amplifier or Subcarrier Detector
   12. 6.12 Communication Interface
       1. 6.12.1 General Introduction
       2. 6.12.2 FIFO Operation
       3. 6.12.3 Parallel Interface Mode
       4. 6.12.4 Reception of Air Interface Data
       5. 6.12.5 Data Transmission to MCU
       6. 6.12.6 Serial Interface Communication (SPI)
          1. 6.12.6.1 Serial Interface Mode Without Slave Select (SS)
          2. 6.12.6.2 Serial Interface Mode With Slave Select (SS)
       7. 6.12.7 Direct Mode
   13. 6.13 Direct Commands from MCU to Reader
       1. 6.13.1  Command Codes
       2. 6.13.2  Reset FIFO (0x0F)
       3. 6.13.3  Transmission With CRC (0x11)
       4. 6.13.4  Transmission Without CRC (0x10)
       5. 6.13.5  Transmit Next Time Slot (0x14)
       6. 6.13.6  Block Receiver (0x16)
       7. 6.13.7  Enable Receiver (0x17)
       8. 6.13.8  Test Internal RF (RSSI at RX Input With TX On) (0x18)
       9. 6.13.9  Test External RF (RSSI at RX Input With TX Off) (0x19)
       10. 6.13.10 Register Preset
   14. 6.14 Register Description
       1. 6.14.1 Register Overview
          1. 6.14.1.1 Main Configuration Registers
             1. 6.14.1.1.1 Chip Status Control Register (0x00)
             2. 6.14.1.1.2 ISO Control Register (0x01)
          2. 6.14.1.2 Protocol Subsetting Registers
             1. 6.14.1.2.1 TX Pulse Length Control Register (0x06)
             2. 6.14.1.2.2 RX No Response Wait Time Register (0x07)
             3. 6.14.1.2.3 RX Wait Time Register (0x08)
             4. 6.14.1.2.4 Modulator and SYS_CLK Control Register (0x09)
             5. 6.14.1.2.5 RX Special Setting Register (0x0A)
             6. 6.14.1.2.6 Regulator and I/O Control Register (0x0B)
          3. 6.14.1.3 Status Registers
             1. 6.14.1.3.1 IRQ Status Register (0x0C)
             2. 6.14.1.3.2 Collision Position and Interrupt Mask Registers (0x0D and 0x0E)
             3. 6.14.1.3.3 RSSI Levels and Oscillator Status Register (0x0F)
          4. 6.14.1.4 Test Registers
             1. 6.14.1.4.1 Test Register (0x1A)
             2. 6.14.1.4.2 Test Register (0x1B)
          5. 6.14.1.5 FIFO Control Registers
             1. 6.14.1.5.1 FIFO Status Register (0x1C)
             2. 6.14.1.5.2 TX Length Byte1 Register (0x1D) and TX Length Byte2 Register (0x1E)
7. 7Applications, Implementation, and Layout
   1. 7.1 TRF7962A Reader System Using SPI With SS Mode
      1. 7.1.1 General Application Considerations
      2. 7.1.2 Schematic
   2. 7.2 System Design
      1. 7.2.1 Layout Considerations
      2. 7.2.2 Impedance Matching TX_Out (Pin 5) to 50 ?
      3. 7.2.3 Reader Antenna Design Guidelines
8. 8器件和文檔支持
   1. 8.1 入門和后續步驟
   2. 8.2 器件命名規則
   3. 8.3 工具和軟件
   4. 8.4 文檔支持
   5. 8.5 社區資源
   6. 8.6 商標
   7. 8.7 靜電放電警告
   8. 8.8 出口管制提示
   9. 8.9 Glossary
9. 9機械、封裝和可訂購信息