成人免费ā片在线观看,亚州超丰滿肉感BBWBBW,人妻少妇精品无码系列

ZHCSPT6D July 2023 – June 2024 TPSM8287A06 , TPSM8287A10 , TPSM8287A12 , TPSM8287A15

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

RDV|39
- MPQF703A

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

9.3.2.4 Selecting the Output Capacitors

If the converter remains in regulation, the minimum required output capacitance is given by:

Equation 46.

C_{O U T (m i n) (r e g)} = (\frac{τ \times (1 + g_{m} \times R_{Comp1})}{2 \times π \times \frac{L}{N?} \times {BW}_{τ}}) (1 + \sqrt{{T O L}_{τ}^{2} + {T O L}_{I N D}^{2} + {T O L}_{f S W}^{2}})

Equation 47.

C_{O U T (m i n) (r e g)} = (\frac{12.5 \times 10^{- 6} \times (1 + 1.5 \times 10^{- 3} \times 2000)}{2 \times π \times \frac{100 \times 10^{- 9}}{4} \times 375 \times 10^{3}}) (1 + \sqrt{{30 %}^{2} + {20 %}^{2} + {10 %}^{2}}) = 1166 μ F

If the converter loop saturates, the minimum output capacitance is given by:

Equation 48.

C_{O U T (m i n) (s a t)} = \frac{1}{? V_{O U T}} (\frac{L \times {? I_{OUT(max)}}^{2}}{2 \times V_{O U T} \times N?} - \frac{? I_{OUT(step)} \times t_{t}}{2}) (1 + {T O L}_{I N D})

Equation 49.

C_{O U T (m i n) (s a t)} = \frac{1}{15 \times 10^{- 3}} (\frac{100 \times 10^{- 9} \times {30.5}^{2}}{2 \times 0.6 \times 4} - \frac{30.0 \times 1 \times 10^{- 6}}{2}) (1 + 20 %) = 345 μ F

In this case, choose C_OUT(min) = 1166 μF as the larger of the two values for the output capacitance.

Table 9-3 lists the output capacitors chosen. 2 × 47-μF capacitors are placed close to each of the four modules, giving a minimum effective capacitance of about 27 μF each. Five 220-μF capacitors and five 47-μF are placed near the load to approximate the total decoupling capacitance required by a typical load. Each of the 220-μF capacitors yield about 138 μF of effective capacitance. Together, the 1041 μF of effective capacitance is very close to the required minimum value calculated above. For further calculations, use C_OUT = 1041 μF.

Equation 50 checks that most of the output capacitance is placed at the load. If the ratio is less than 1, increase the capacitance at the load or place the device, output capacitance, and load next to each other such that there is no separation between the output capacitances.

Equation 50.

\frac{C_{LOAD}}{2 {\times C}_{OUT}} > 1

Equation 51.

\frac{5 \times 27 \times 10^{- 6} + 5 \times 138 \times 10^{- 6}}{2 \times (4 \times 2 \times 27 \times 10^{- 6})} > 1

= True

Equation 52 calculates the output voltage ripple, based on the effective output capacitance value.

Equation 52.

V_{O U T (p - p)} = \frac{I_{L (PP)}}{8 \times C_{OUT} \times f_{s w}}

Equation 53.

V_{O U T (p - p)} = \frac{0.9}{8 \times 1041 \times 10^{- 6} \times 1.5 \times 10^{6}} = 0.072 m V

The ripple is slightly higher in the application due to the ESR and ESL in the output capacitors and the application board parasitics.