ZHCSN60D November 2021 – March 2024 TLV9161 , TLV9162 , TLV9164
PRODUCTION DATA
| 參數 | 測試條件 | 最小值 | 典型值 | 最大值 | 單位 | ||
|---|---|---|---|---|---|---|---|
| 失調電壓 | |||||||
| VOS | 輸入失調電壓 | VCM = V– | ±0.21 | ±1 | mV | ||
| TA = -40°C 至 125°C | ±1.2 | ||||||
| dVOS/dT | 輸入失調電壓溫漂 | VCM = V– | TA = -40°C 至 125°C | ±0.25 | μV/℃ | ||
| PSRR | 輸入失調電壓與電源間的關系 | TLV9161，TLV9162，VCM = V–，VS = 5V 至 16V | ±0.45 | ±2 | μV/V | ||
| TA = -40°C 至 125°C | ±0.45 | ±3 | |||||
| TLV9162SIRUGR，VCM = V–，VS = 5V 至 16V(1) | ±0.45 | ±2.8 | |||||
| TA = -40°C 至 125°C | ±0.45 | ±3.1 | |||||
| TLV9164，VCM = V–，VS = 5V 至 16V | ±0.45 | ±2.2 | |||||
| TA = -40°C 至 125°C | ±0.45 | ±3.8 | |||||
| TLV9161，TLV9162，TLV9164，VCM = V–，VS = 2.7V 至 16V(1) | TA = -40°C 至 125°C | ±2 | ±12 | ||||
| 直流通道隔離 | 0.4 | μV/V | |||||
| 輸入偏置電流 | |||||||
| IB | 輸入偏置電流 | ±10 | pA | ||||
| IOS | 輸入失調電流 | ±10 | pA | ||||
| 噪聲 | |||||||
| EN | 輸入電壓噪聲 | f = 0.1Hz 至 10Hz | 2.7 | μVPP | |||
| 0.49 | μVRMS | ||||||
| eN | 輸入電壓噪聲密度 | f = 1kHz | 6.8 | nV/√Hz | |||
| f = 10kHz | 4.2 | ||||||
| iN | 輸入電流噪聲密度 | f = 1kHz | 55 | fA/√Hz | |||
| 輸入電壓范圍 | |||||||
| VCM | 共模電壓范圍 | (V–) | (V+) | V | |||
| CMRR | 共模抑制比 | VS = 16V，V– < VCM < (V+) – 2V（PMOS 對） | TA = -40°C 至 125°C | 85 | 110 | dB | |
| VS = 5V，V– < VCM < (V+) – 2V（PMOS 對）(1) | 75 | 98 | |||||
| VS = 2.7V，V– < VCM < (V+) – 2V（PMOS 對） | 90 | ||||||
| VS = 2.7V 至 16V，(V+) – 1V < VCM < V+（NMOS 對） | 78 | ||||||
| (V+) – 2V < VCM < (V+) – 1V | 請參閱圖 5-6 | ||||||
| 輸入阻抗 | |||||||
| ZID | 差分 | 100 || 9 | MΩ || pF | ||||
| ZICM | 共模 | 6 || 1 | TΩ || pF | ||||
| 開環增益 | |||||||
| AOL | 開環電壓增益 | VS = 16V，VCM = VS / 2， (V–) + 0.1V < VO < (V+) – 0.1V |
120 | 136 | dB | ||
| TA = -40°C 至 125°C | 136 | ||||||
| VS = 5V，VCM = VS / 2， (V–) + 0.1V < VO < (V+) – 0.1V(1) |
104 | 125 | |||||
| TA = -40°C 至 125°C | 125 | ||||||
| VS = 2.7V，VCM = VS / 2， (V–) + 0.1V < VO < (V+) – 0.1V(1) |
90 | 105 | |||||
| TA = -40°C 至 125°C | 105 | ||||||
| 頻率響應 | |||||||
| GBW | 增益帶寬積 | 11 | MHz | ||||
| SR | 壓擺率 | VS = 16V，G = +1，VSTEP = 10V，CL = 20pF(3) | 33 | V/μs | |||
| tS | 穩定時間 | 精度為 0.1%，VS = 16V，VSTEP = 10V，G = +1，CL = 20pF | 0.70 | μs | |||
| 精度為 0.1%，VS = 16V，VSTEP = 2V，G = +1，CL = 20pF | 0.22 | ||||||
| 精度為 0.01%，VS = 16V，VSTEP = 10V，G = +1，CL = 20pF | 0.89 | ||||||
| 精度為 0.01%，VS = 16V，VSTEP = 2V，G = +1，CL = 20pF | 0.42 | ||||||
| 相位裕度 | G = +1，RL = 10k?，CL = 20pF | 64 | ° | ||||
| 過載恢復時間 | VIN × 增益 > VS | 120 | ns | ||||
| THD+N | 總諧波失真 + 噪聲 | VS = 16V，VO = 3VRMS，G = 1，f = 1kHz | 0.00005% | ||||
| 126 | dB | ||||||
| VS = 10V，VO = 3VRMS，G = 1，f = 1kHz，RL = 128Ω | 0.0032% | ||||||
| 90 | dB | ||||||
| VS = 10V，VO = 0.4VRMS，G = 1，f = 1kHz，RL = 32Ω | 0.00032% | ||||||
| 110 | dB | ||||||
| 輸出 | |||||||
| 相對于電源軌的電壓輸出擺幅 | 正負 電源軌余量 |
VS = 16V，RL = 空載 | 6 | mV | |||
| VS = 16V，RL = 10kΩ | 25 | 60 | |||||
| VS = 16V，RL = 2kΩ | 85 | 300 | |||||
| VS = 2.7V，RL = 空載 | 0.5 | ||||||
| VS = 2.7V，RL = 10kΩ | 5 | 20 | |||||
| VS = 2.7V，RL = 2kΩ | 20 | 50 | |||||
| ISC | 短路電流 | ±73 | mA | ||||
| CLOAD | 容性負載驅動 | 請參閱圖 5-33 | pF | ||||
| ZO | 開環輸出阻抗 | IO = 0A | 請參閱圖 5-30 | ? | |||
| 電源 | |||||||
| IQ | 每個放大器的靜態電流 | TLV9162，TLV9164，IO = 0A | 2.4 | 2.8 | mA | ||
| TA = -40°C 至 125°C | 2.84 | ||||||
| TLV9161，IO = 0A | 2.48 | 2.92 | |||||
| TA = -40°C 至 125°C | 2.98 | ||||||
| 關斷 | |||||||
| IQSD | 每個放大器的靜態電流 | VS = 2.7V 至 16V，所有放大器都被禁用，SHDN = V– + 2V | 36 | 45 | μA | ||
| ZSHDN | 關斷時的輸出阻抗 | VS = 2.7V 至 16V，放大器被禁用 | 10 || 2 | GΩ || pF | |||
| VIH | 邏輯高電平閾值電壓（放大器被禁用） | 對于有效輸入高電平，SHDN 引腳電壓應大于最大閾值，但小于或等于 V+ | (V–) + 1.1V |
V | |||
| VIL | 邏輯低電平閾值電壓（放大器被啟用） | 對于有效輸入低電平，SHDN 引腳電壓應該小于最小閾值，但大于或等于 V– | (V–) + 0.2V |
V | |||
| tON | 放大器啟用時間（從關斷開始）(2) | VS = ±8V，G = +1，VCM = VS/2，RL = 10k?（連接至 V-） | 5 | μs | |||
| tOFF | 放大器禁用時間(2) | VS = ±8V，G = +1，VCM = VS/2，RL = 10k?（連接至 V-） | 3 | μs | |||
| SHDN 引腳輸入偏置電流（每個引腳） | VS = 2.7V 至 16V，(V+) ≥ SHDN ≥ (V–) + 0.9V | 500 | nA | ||||
| VS = 2.7V 至 16V，(V–) ≤ SHDN ≤ (V–) + 0.7V | 400 | ||||||