ZHCSIR8F August 2009 – September 2018 MSP430F5418 , MSP430F5419 , MSP430F5435 , MSP430F5436 , MSP430F5437 , MSP430F5438
PRODUCTION DATA.
- 1器件概述
- 2修訂歷史記錄
- 3Device Comparison
- 4Terminal Configuration and Functions
-
5Specifications
- 5.1 Absolute Maximum Ratings
- 5.2 ESD Ratings
- 5.3 Recommended Operating Conditions
- 5.4 Active Mode Supply Current Into VCC Excluding External Current
- 5.5 Low-Power Mode Supply Currents (Into VCC) Excluding External Current
- 5.6 Thermal Resistance Characteristics
- 5.7 Schmitt-Trigger Inputs – General-Purpose I/O
- 5.8 Inputs – Ports P1 and P2
- 5.9 Leakage Current – General-Purpose I/O
- 5.10 Outputs – General-Purpose I/O (Full Drive Strength)
- 5.11 Outputs – General-Purpose I/O (Reduced Drive Strength)
- 5.12 Output Frequency – General-Purpose I/O
- 5.13 Typical Characteristics – Outputs, Reduced Drive Strength (PxDS.y = 0)
- 5.14 Typical Characteristics – Outputs, Full Drive Strength (PxDS.y = 1)
- 5.15 Crystal Oscillator, XT1, Low-Frequency Mode
- 5.16 Crystal Oscillator, XT1, High-Frequency Mode
- 5.17 Crystal Oscillator, XT2
- 5.18 Internal Very-Low-Power Low-Frequency Oscillator (VLO)
- 5.19 Internal Reference, Low-Frequency Oscillator (REFO)
- 5.20 DCO Frequency
- 5.21 PMM, Brownout Reset (BOR)
- 5.22 PMM, Core Voltage
- 5.23 PMM, SVS High Side
- 5.24 PMM, SVM High Side
- 5.25 PMM, SVS Low Side
- 5.26 PMM, SVM Low Side
- 5.27 Wake-up Times From Low-Power Modes
- 5.28 Timer_A
- 5.29 Timer_B
- 5.30 USCI (UART Mode) Clock Frequency
- 5.31 USCI (UART Mode)
- 5.32 USCI (SPI Master Mode) Clock Frequency
- 5.33 USCI (SPI Master Mode)
- 5.34 USCI (SPI Slave Mode)
- 5.35 USCI (I2C Mode)
- 5.36 12-Bit ADC, Power Supply and Input Range Conditions
- 5.37 12-Bit ADC, External Reference
- 5.38 12-Bit ADC, Built-In Reference
- 5.39 12-Bit ADC, Timing Parameters
- 5.40 12-Bit ADC, Linearity Parameters
- 5.41 12-Bit ADC, Temperature Sensor and Built-In VMID
- 5.42 Flash Memory
- 5.43 JTAG and Spy-Bi-Wire Interface
-
6Detailed Description
- 6.1 CPU
- 6.2 Operating Modes
- 6.3 Interrupt Vector Addresses
- 6.4 Memory Organization
- 6.5 Bootloader (BSL)
- 6.6 JTAG Operation
- 6.7 Flash Memory (Link to User's Guide)
- 6.8 RAM (Link to User's Guide)
- 6.9
Peripherals
- 6.9.1 Digital I/O (Link to User's Guide)
- 6.9.2 Oscillator and System Clock (Link to User's Guide)
- 6.9.3 Power-Management Module (PMM) (Link to User's Guide)
- 6.9.4 Hardware Multiplier (Link to User's Guide)
- 6.9.5 Real-Time Clock (RTC_A) (Link to User's Guide)
- 6.9.6 Watchdog Timer (WDT_A) (Link to User's Guide)
- 6.9.7 System Module (SYS) (Link to User's Guide)
- 6.9.8 DMA Controller (Link to User's Guide)
- 6.9.9 Universal Serial Communication Interface (USCI) (Links to User's Guide: UART Mode, SPI Mode, I2C Mode)
- 6.9.10 TA0 (Link to User's Guide)
- 6.9.11 TA1 (Link to User's Guide)
- 6.9.12 TB0 (Link to User's Guide)
- 6.9.13 ADC12_A (Link to User's Guide)
- 6.9.14 CRC16 (Link to User's Guide)
- 6.9.15 Embedded Emulation Module (EEM) (L Version) (Link to User's Guide)
- 6.9.16 Peripheral File Map
- 6.10
Input/Output Diagrams
- 6.10.1 Port P1, P1.0 to P1.7, Input/Output With Schmitt Trigger
- 6.10.2 Port P2, P2.0 to P2.7, Input/Output With Schmitt Trigger
- 6.10.3 Port P3, P3.0 to P3.7, Input/Output With Schmitt Trigger
- 6.10.4 Port P4, P4.0 to P4.7, Input/Output With Schmitt Trigger
- 6.10.5 Port P5, P5.0 and P5.1, Input/Output With Schmitt Trigger
- 6.10.6 Port P5, P5.2, Input/Output With Schmitt Trigger
- 6.10.7 Port P5, P5.3, Input/Output With Schmitt Trigger
- 6.10.8 Port P5, P5.4 to P5.7, Input/Output With Schmitt Trigger
- 6.10.9 Port P6, P6.0 to P6.7, Input/Output With Schmitt Trigger
- 6.10.10 Port P7, P7.0, Input/Output With Schmitt Trigger
- 6.10.11 Port P7, P7.1, Input/Output With Schmitt Trigger
- 6.10.12 Port P7, P7.2 and P7.3, Input/Output With Schmitt Trigger
- 6.10.13 Port P7, P7.4 to P7.7, Input/Output With Schmitt Trigger
- 6.10.14 Port P8, P8.0 to P8.7, Input/Output With Schmitt Trigger
- 6.10.15 Port P9, P9.0 to P9.7, Input/Output With Schmitt Trigger
- 6.10.16 Port P10, P10.0 to P10.7, Input/Output With Schmitt Trigger
- 6.10.17 Port P11, P11.0 to P11.2, Input/Output With Schmitt Trigger
- 6.10.18 Port J, J.0 JTAG Pin TDO, Input/Output With Schmitt Trigger or Output
- 6.10.19 Port J, J.1 to J.3 JTAG Pins TMS, TCK, TDI/TCLK, Input/Output With Schmitt Trigger or Output
- 6.11 TLV (Device Descriptor) Structures
- 7器件和文檔支持
- 8機械，封裝和可訂購信息
封裝選項
機械數據 (封裝 | 引腳)
- PZ|100
散熱焊盤機械數據 (封裝 | 引腳)
訂購信息
6.10.15 Port P9, P9.0 to P9.7, Input/Output With Schmitt Trigger
Figure 6-16 shows the port diagram. Table 6-54 summarizes the selection of the pin function.
Figure 6-16 Port P9 (P9.0 to P9.7) Diagram Table 6-54 Port P9 (P9.0 to P9.7) Pin Functions
| PIN NAME (P9.x) | x | FUNCTION | CONTROL BITS OR SIGNALS(1) | |
|---|---|---|---|---|
| P9DIR.x | P9SEL.x | |||
| P9.0/UCB2STE/UCA2CLK | 0 | P9.0 (I/O) | I: 0; O: 1 | 0 |
| UCB2STE/UCA2CLK(2)(4) | X | 1 | ||
| P9.1/UCB2SIMO/UCB2SDA | 1 | P9.1 (I/O) | I: 0; O: 1 | 0 |
| UCB2SIMO/UCB2SDA(2)(3) | X | 1 | ||
| P9.2/UCB2SOMI/UCB2SCL | 2 | P9.2 (I/O) | I: 0; O: 1 | 0 |
| UCB2SOMI/UCB2SCL(2)(3) | X | 1 | ||
| P9.3/UCB2CLK/UCA2STE | 3 | P9.3 (I/O) | I: 0; O: 1 | 0 |
| UCB2CLK/UCA2STE(2) | X | 1 | ||
| P9.4/UCA2TXD/UCA2SIMO | 4 | P9.4 (I/O) | I: 0; O: 1 | 0 |
| UCA2TXD/UCA2SIMO(2) | X | 1 | ||
| P9.5/UCA2RXD/UCA2SOMI | 5 | P9.5 (I/O) | I: 0; O: 1 | 0 |
| UCA2RXD/UCA2SOMI(2) | X | 1 | ||
| P9.6 | 6 | P9.6 (I/O) | I: 0; O: 1 | 0 |
| P9.7 | 7 | P9.7 (I/O) | I: 0; O: 1 | 0 |
(1) X = Don't care
(2) The pin direction is controlled by the USCI module.
(3) If the I2C functionality is selected, the output drives only the logical 0 to VSS level.
(4) UCB2CLK function takes precedence over UCA2STE function. If the pin is required as UCB2CLK input or output, USCI_A2 is forced to 3-wire SPI mode if 4-wire SPI mode is selected.