ZHCSFB5D July 2016 – December 2017 LM5141-Q1
PRODUCTION DATA.
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|
| VIN SUPPLY VOLTAGE | ||||||
| ISHUTDOWN | Shutdown mode current | VIN = 8–18 V, EN = 0 V, VCCX = 0 V | 10 | 12.5 | µA | |
| ISTANDBY | Standby current | EN = 5 V, FB = VDD, VOUT in regulation, no-load, not switching, DEMB = GND. | 35 | 45 | µA | |
| EN = 5 V, FB = 0 V, VOUT in regulation, no-load, not switching, VCCX = 5 V, DEMB = GND. | 42 | 55 | ||||
| VCC REGULATOR | ||||||
| VCC(REG) | VCC regulation voltage | VIN = 6 to 18 V, 0 to 75 mA, VCCX = 0 V | 4.75 | 5 | 5.25 | V |
| VCC(UVLO) | VCC undervoltage threshold | VCC rising, VCCX = 0 V | 3.25 | 3.4 | 3.55 | V |
| VCC(HYST) | VCC hysteresis voltage | VCCX = 0 V | 175 | mV | ||
| ICC(LIM) | VCC sourcing current limit | VCCX = 0 V | 85 | 125 | mA | |
| VDDA | ||||||
| VDDA(REG) | Internal bias supply power | VCCX = 0 V | 4.75 | 5 | 5.25 | V |
| VDDA(UVLO) | VCC rising, VCCX = 0 V | 3.1 | 3.2 | 3.3 | V | |
| VDDA(HYST) | VCCX = 0 V | 125 | mV | |||
| RVDDA | VCCX = 0 V | 55 | Ω | |||
| VCCX | ||||||
| VCCX(ON) | VCC rising | 4.1 | 4.3 | 4.4 | V | |
| VCCX(HYST) | 80 | mV | ||||
| R(VCCX) | VCCX = 5 V | 2 | Ω | |||
| OSCILLATOR SELECT THRESHOLDS | ||||||
| Oscillator select threshold 2.2 MHz | (OSC pin) | 2.0 | V | |||
| Oscillator select threshold 440 kHz | (OSC pin) | 0.8 | V | |||
| CURENT LIMIT | ||||||
| V(CS) | Current limit threshold | ILSET = VDDA, measure from CS to VOUT | 68 | 75 | 82 | mV |
| tdly | Current sense delay to output | 40 | ns | |||
| Current sense amplifier gain | 11.4 | 12 | 12.6 | V/V | ||
| ICS(BIAS) | Amplifier input bias | 10 | nA | |||
| RES | ||||||
| I(RES) | RES current source | 20 | µA | |||
| V(RES) | RES threshold | 1.2 | V | |||
| Timer | Timer hiccup mode fault | 512 | cycles | |||
| RDS(ON) | RES pulldown | 4 | Ω | |||
| OUTPUT VOLTAGE REGULATION | ||||||
| 3.3 V | VIN = 3.8 to 42 V | 3.273 | 3.3 | 3.327 | V | |
| 5 V | VIN = 5.5 to 42 V | 4.96 | 5.0 | 5.04 | V | |
| FEEDBACK | ||||||
| VOUT select threshold 3.3 V | VDD - 0.3 | V | ||||
| Regulated feedback voltage | 1.193 | 1.2 | 1.207 | V | ||
| FB(LOWRES) | Resistance to ground on FB for FB = 0 detection | 500 | Ω | |||
| FB(EXTRES) | Thevenin equivalent resistance at FB for external regulation detection | FB < 2 V | 5 | kΩ | ||
| TRANSCONDUCTANCE AMPLIFIER | ||||||
| Gm | Gain | Feedback to COMP | 1010 | 1200 | µS | |
| Input bias current | 15 | nA | ||||
| Transconductance amplifier source current | COMP = 1 V, FB = 1 V | 100 | µA | |||
| Transconductance amplifier sink current | COMP = 1 V, FB = 1.4 V | 100 | µA | |||
| POWER GOOD | ||||||
| PG(UV) | PG undervoltage trip levels | Falling with respect to the regulation voltage | 90% | 92% | 94% | |
| PG(OVP) | PG overvoltage trip levels | Rising with respect to the regulation voltage | 108% | 110% | 112% | |
| PG(HYST) | 3.4% | |||||
| PG(VOL) | PG | Open collector, Isink = 2 mA | 0.4 | V | ||
| PG(rdly) | OV filter time | VOUT rising | 25 | µs | ||
| PG(fdly) | UV filter time | VOUT falling | 30 | µs | ||
| HO GATE DRIVER | ||||||
| VOLH | HO Low-state output voltage | IHO = 100 mA | 0.05 | V | ||
| VOHH | HO High-state output voltage | IHO = –100 mA, VOHH = VHB - VHO | 0.07 | V | ||
| trHO | HO rise time (10% to 90%) | CLOAD = 2700 pf | 4 | ns | ||
| tfHO | HO fall time (90% to 10%) | CLOAD = 2700 pf | 3 | ns | ||
| IOHH | HO peak source current | VHO = 0 V, SW = 0 V, HB = 5 V, VCCX = 5 V | 3.25 | Apk | ||
| IOLH | HO peak sink current | VCCX = 5 V | 4.25 | Apk | ||
| V(BOOT) | UVLO | HO falling | 2.5 | V | ||
| Hysteresis | 110 | mV | ||||
| I(BOOT) | Quiescent current | 3 | µA | |||
| LO GATE DRIVER | ||||||
| VOLL | LO Low-state output voltage | ILO = 100 mA | 0.05 | V | ||
| VOHL | LO High-state output voltage | ILO = –100 mA, VOHL = VCC – VLO | 0.07 | V | ||
| trLO | LO rise time (10% to 90%) | CLOAD = 2700 pf | 4 | ns | ||
| tfLO | LO fall time (90% to 10%) | CLOAD = 2700 pf | 3 | ns | ||
| IOHL | LO peak source current | VCCX = 5 V | 3.25 | Apk | ||
| IOLL | LO peak sink current | VCCX = 5 V | 4.25 | Apk | ||
| ADAPTIVE DEAD TIME CONTROL | ||||||
| V(GS-DET) | VGS detection threshold | VGS falling, no load | 2.5 | V | ||
| tdly1 | HO off to LO on dead time | 20 | 40 | ns | ||
| tdly2 | LO off to HO on dead time | 20 | 38 | ns | ||
| DIODE EMULATION | ||||||
| VIL | DEMB input low threshold | 0.8 | V | |||
| VIH | FPWM input high threshold | 2 | V | |||
| SW | Zero cross threshold | –5 | mV | |||
| ENABLE INPUT | ||||||
| VIL | Enable input low threshold | VCCX = 0 V | 0.8 | V | ||
| VIH | Enable input high threshold | VCCX = 0 V | 2.0 | V | ||
| IIkg | Leakage | EN logic input only | 1 | µA | ||
| SYN INPUT (DEMB pin) | ||||||
| VIL | DEMB input low threshold | 0.8 | V | |||
| VIH | DEMB input high threshold | 2 | V | |||
| DEMB input low frequency range 440 kHz | 350 | 550 | kHz | |||
| DEMB input high frequency range 2.2 MHz | 1800 | 2600 | kHz | |||
| DITHER | ||||||
| IDITHER | Dither source/sink current | 20 | µA | |||
| VDITHER | Dither high threshold | 1.26 | V | |||
| Dither low threshold | 1.14 | V | ||||
| SOFT-START | ||||||
| ISS | Soft-Start current | 16 | 22 | 28 | µA | |
| RDS(ON) | Soft-Start pull-down resistance | 3 | Ω | |||
| THERMAL | ||||||
| TSD Thermal Shutdown | 175 | ºC | ||||
| Thermal shutdown hysteresis | 15 | ºC | ||||