ZHCSOS0C august 2021 – june 2023 MCF8316A
PRODUCTION DATA
- 1
- 1 特性
- 2 應用
- 3 Description
- 4 Revision History
- 5 Pin Configuration and Functions
- 6 Specifications
-
7 Detailed Description
- 7.1 Overview
- 7.2 Functional Block Diagram
- 7.3
Feature Description
- 7.3.1 Output Stage
- 7.3.2 Device Interface Modes
- 7.3.3 Step-Down Mixed-Mode Buck Regulator
- 7.3.4 AVDD Linear Voltage Regulator
- 7.3.5 Charge Pump
- 7.3.6 Slew Rate Control
- 7.3.7 Cross Conduction (Dead Time)
- 7.3.8 SPEED Control
- 7.3.9 Starting the Motor Under Different Initial Conditions
- 7.3.10 Motor Start Sequence (MSS)
- 7.3.11 Closed Loop Operation
- 7.3.12 Motor Parameters
- 7.3.13 Motor Parameter Extraction Tool (MPET)
- 7.3.14 Anti-Voltage Surge (AVS)
- 7.3.15 Output PWM Switching Frequency
- 7.3.16 Active Braking
- 7.3.17 PWM Modulation Schemes
- 7.3.18 Dead Time Compensation
- 7.3.19 Motor Stop Options
- 7.3.20 FG Configuration
- 7.3.21 DC Bus Current Limit
- 7.3.22
Protections
- 7.3.22.1 VM Supply Undervoltage Lockout
- 7.3.22.2 AVDD Undervoltage Lockout (AVDD_UV)
- 7.3.22.3 BUCK Undervoltage Lockout (BUCK_UV)
- 7.3.22.4 VCP Charge Pump Undervoltage Lockout (CPUV)
- 7.3.22.5 Overvoltage Protection (OVP)
- 7.3.22.6 Overcurrent Protection (OCP)
- 7.3.22.7 Buck Overcurrent Protection
- 7.3.22.8 Hardware Lock Detection Current Limit (HW_LOCK_ILIMIT)
- 7.3.22.9 Thermal Warning (OTW)
- 7.3.22.10 Thermal Shutdown (TSD)
- 7.3.22.11 Motor Lock (MTR_LCK)
- 7.3.22.12 Motor Lock Detection
- 7.3.22.13 MPET Faults
- 7.3.22.14 IPD Faults
- 7.4 Device Functional Modes
- 7.5 External Interface
- 7.6 EEPROM access and I2C interface
- 7.7 EEPROM (Non-Volatile) Register Map
- 7.8 RAM (Volatile) Register Map
- 8 Application and Implementation
- 9 Power Supply Recommendations
- 10Layout
- 11Device and Documentation Support
- 12Mechanical, Packaging, and Orderable Information
7.3.19.3 Low-Side Braking
Low-side braking mode is configured by setting MTR_STOP to 010b. When a motor stop command is received, the output speed is reduced to a value defined by BRAKE_SPEED_THRESHOLD prior to turning all low-side MOSFETs ON (see example Figure 7-43) for a time configured by MTR_STOP_BRK_TIME. If the motor speed is below BRAKE_SPEED_THRESHOLD prior to receiving stop command, then the MCF8316A transitions directly into the brake state. After applying the brake for MTR_STOP_BRK_TIME, the MCF8316A transitions into the Hi-Z state by turning OFF all MOSFETs.
Figure 7-43 Low-Side BrakingThe MCF8316A can also enter low-side braking through BRAKE pin input. When BRAKE pin is pulled to HIGH state, the output speed is reduced to a value defined by BRAKE_SPEED_THRESHOLD prior to turning all low-side MOSFETs ON. In this case, MCF8316A stays in low-side brake state till BRAKE pin changes to LOW state.