ZHCSLW2C September 2021 – April 2022 ISOW7740 , ISOW7741 , ISOW7742 , ISOW7743 , ISOW7744
PRODUCTION DATA
- 1 特性
- 2 應用
- 3 說明
- 4 Revision History
- 5 說明（接續）
- 6 Pin Configuration and Functions
-
7 Specifications
- 7.1 Absolute Maximum Ratings
- 7.2 ESD Ratings
- 7.3 Recommended Operating Conditions
- 7.4 Thermal Information
- 7.5 Power Ratings
- 7.6 Insulation Specifications
- 7.7 Safety-Related Certifications
- 7.8 Safety Limiting Values
- 7.9 Electrical Characteristics - Power Converter
- 7.10 Supply Current Characteristics - Power Converter
- 7.11 Electrical Characteristics Channel Isolator - VIO, VISOIN = 5-V
- 7.12 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 5-V
- 7.13 Electrical Characteristics Channel Isolator - VIO, VISOIN = 3.3-V
- 7.14 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 3.3-V
- 7.15 Electrical Characteristics Channel Isolator - VIO, VISOIN = 2.5-V
- 7.16 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 2.5-V
- 7.17 Electrical Characteristics Channel Isolator - VIO, VISOIN = 1.8-V
- 7.18 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 1.8-V
- 7.19 Switching Characteristics - 5-V Supply
- 7.20 Switching Characteristics - 3.3-V Supply
- 7.21 Switching Characteristics - 2.5-V Supply
- 7.22 Switching Characteristics - 1.8-V Supply
- 7.23 Insulation Characteristics Curves
- 7.24 Typical Characteristics
- 8 Parameter Measurement Information
- 9 Detailed Description
- 10Application and Implementation
- 11Power Supply Recommendations
- 12Layout
- 13Device and Documentation Support
- 14Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- DFM|20
散熱焊盤機械數據 (封裝 | 引腳)
訂購信息
8 Parameter Measurement Information
In the below images, VCCI and
VCCO refers to the power supplies VIO and VISOIN,
respectively.
A. CL = 15 pF and The
input pulse is supplied by a generator having the following characteristics: PRR
≤ 50 kHz, 50% duty cycle, tr ≤ 3 ns, tf ≤ 3ns,
ZO = 50 Ω. At the input, 50 Ω resistor is required to terminate
Input Generator signal. It is not needed in actual application.
B. B. CL = 15 pF and
includes instrumentation and fixture capacitance within ±20%.
Figure 8-1 Switching
Characteristics Test Circuit and Voltage Waveforms
A. A. The input pulse is supplied by
a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle,
tr ≤ 3 ns, tf ≤ 3ns, ZO = 50 Ω. At the
input, 50 Ω resistor is required to terminate Input Generator signal. It is not
needed in actual application.
B. B. CL = 15 pF and
includes instrumentation and fixture capacitance within ±20%.
Figure 8-2 Enable/Disable Propagation
Delay Time Test Circuit and Waveform
Note: A. CL = 15 pF and includes instrumentation and fixture capacitance
within ±20%.
Note: B. Power Supply Ramp Rate = 10 mV/ns.
Figure 8-3 Default Output Delay Time Test Circuit and Voltage WaveformsNote: CL = 15 pF and includes instrumentation and fixture capacitance
within ±20%.
Note: Pass-fail criteria: Outputs must remain stable.
Figure 8-4 Common-Mode Transient Immunity Test Circuit