日韩超碰人人爽人人做人人添,久久久WWW免费人成精品 ,亚洲色欲AV无码成人专区

ZHCSG74B april 2017 – april 2023 AMC1301-Q1

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

DWV|8
- MPDS382B

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

6.9 Electrical Characteristics

minimum and maximum specifications apply from T_A = –40°C to +125°C, VDD1 = 3.0 V to 5.5 V, VDD2 = 3.0 V to 5.5 V, INP = –250 mV to +250 mV, and INN = GND1; typical specifications are at T_A = 25°C, VDD1 = 5 V, and VDD2 = 3.3 V (unless otherwise noted)

PARAMETER		TEST CONDITIONS	MIN	TYP	MAX	UNIT
ANALOG INPUT
V_CMov	Common-mode overvoltage detection level	(V_INP+ V_INN) / 2 to GND1	VDD1 – 2			V
	Hysteresis of common-mode overvoltage detection level			60		mV
V_OS	Input offset voltage⁽¹⁾	Initial, at T_A = 25°C, INP = INN = GND1	–0.2	±0.05	0.2	mV
TCV_OS	Input offset drift⁽¹⁾⁽⁴⁾		–3	±1	3	μV/°C
CMRR	Common-mode rejection ratio	f_IN = 0 Hz, V_{CM min} ≤ V_CM ≤ V_{CM max}		–93		dB
CMRR	Common-mode rejection ratio	f_IN = 10 kHz, V_{CM min} ≤ V_CM ≤ V_{CM max}		–93		dB
R_IN	Single-ended input resistance	INN = GND1		18		kΩ
R_IND	Differential input resistance			22		kΩ
I_IB	Input bias current	INP = INN = GND1; I_IB = (I_IBP + I_IBN) / 2	–41	–30	–24	μA
TCI_IB	Input bias current drift			1		nA/°C
C_IND	Differential input capacitance			1		pF
ANALOG OUTPUT
	Nominal gain			8.2		V/V
E_G	Gain error⁽¹⁾	at T_A = 25°C	–0.3%	±0.05%	0.3%
TCE_G	Gain drift⁽¹⁾⁽⁵⁾		–50	±15	50	ppm/°C
	Nonlinearity⁽¹⁾		–0.03%	±0.01%	0.03%
	Nonlinearity drift			±1		ppm/°C
THD	Total harmonic distortion⁽³⁾	f_IN = 10 kHz		–87		dB
	Output noise	INP = INN = GND1, f_IN = 0 Hz, BW = 100 kHz brickwall filter		220		μV_RMS
SNR	Signal-to-noise ratio	f_IN = 1 kHz, BW = 10 kHz	80	84		dB
SNR	Signal-to-noise ratio	f_IN = 10 kHz, BW = 100 kHz		71		dB
PSRR	Power-supply rejection ratio⁽²⁾	PSRR vs VDD1, at DC		–94		dB
		PSRR vs VDD1, 100-mV and 10-kHz ripple		–90
		PSRR vs VDD2, at DC		–100
		PSRR vs VDD2, 100-mV and 10-kHz ripple		–94
V_CMout	Common-mode output voltage		1.39	1.44	1.49	V
V_CLIPout	Clipping differential output voltage	V_OUT = (V_OUTP – V_OUTN); \|V_IN\| = \|V_INP – V_INN\| > \|V_Clipping\|	–2.52	±2.49	2.52	V
V_Failsafe	Failsafe differential output voltage	V_CM ≥ V_CMov, or VDD1 missing		–2.563	–2.545	V
BW	Output bandwidth		190	210		kHz
R_OUT	Output resistance	On OUTP or OUTN		< 0.2		Ω
	Output short-circuit current	On OUTP or OUTN, sourcing or sinking, INN = INP = GND1, outputs shorted to either GND2 or VDD2		13		mA
CMTI	Common-mode transient immunity	\|GND1 – GND2\| = 1 kV	15			kV/μs
POWER SUPPLY
IDD1	High-side supply current	3.0 V ≤ VDD1 ≤ 3.6 V		6.3	8.5	mA
IDD1	High-side supply current	4.5 V ≤ VDD1 ≤ 5.5 V		7.2	9.8	mA
IDD2	Low-side supply current	3.0 V ≤ VDD2 ≤ 3.6 V		5.3	7.2	mA
IDD2	Low-side supply current	4.5 V ≤ VDD2 ≤ 5.5 V		5.9	8.1	mA

(1) The typical value includes one standard deviation (sigma) at nominal operating conditions.

(2) This parameter is input referred.

(3) THD is the ratio of the rms sum of the amplitues of first five higher harmonics to the amplitude of the fundamental.

(4) Offset error temperature drift is calculated using the box method, as described by the following equation:
TCV_OS = (V_OS,MAX - V_OS,MIN) / TempRange where V_OS,MAX and V_OS,MIN refer to the maximum and minimum V_OS values measured within the temperature range (–40 to 125℃).

(5) Gain error temperature drift is calculated using the box method, as described by the following equation:
TCE_G (ppm) = ((E_G,MAX - E_G,MIN) / TempRange) x 10⁴ where E_G,MAX and E_G,MIN refer to the maximum and minimum E_G values (in %) measured within the temperature range (–40 to 125℃).